28360
31
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
24
Rotate the J-DIAL clockwise for outer direction or counterclockwise
for inner direction to move the #2 variable range marker. The actual
target distance appears on the center top of the screen in selecting unit.
To turn off the #2 VRM, selects the FUNCTION-#2 VRM-OFF on the
menu sheet.
(4) Using cursor
Touch the JOYSTICK, cross cursor appears on the screen. The cross mark
will be move any direction by using the JOYSTICK and the range and bear-
ing Time-To-Go data and Lat/Loug of the cursor position will be displayed
on the lower right corner on the display.
The cross cursor and cursor data will disappear in approximately 15 sec-
onds.
4.12 BEARING MEASUREMENT
(1) Using the bearing scale
Using the bearing scale on the screen, visually estimate the bearing where
the radial line of the bearing scale would pass through the center of the
target. The bearing you obtain will be the target’s relative bearing in de-
grees.
(2) Using #1 EBL
Press the EBL/VRM key.
If VRM is highlighted, press and hold the EBL/VRM key to change to EBL
mode.
Rotate the J-DIAL clockwise or counterclockwise to move the electronic
bearing line to the center of the target. Target bearing appears on the center
top of the screen in degrees. Bearing may be displayed in relative “R”, true
“T”, or magnetic “M” depending on the menu selection.
To turn off the EBL, press the EBL/VRM key while EBL is highlighted.
(3) Using #2 EBL
Press the JOYSTICK.
Selects FUNCTION menu, then press the JOYSTICK.
Selects #2 EBL-SET, then press the JOYSTICK. The EBL2 appears high-
light on the upper right corner of the display.
Rotate the J-DIAL clockwise or counterclockwise to move the #2 EBL
OPERATION
24
Rotate the J-DIAL clockwise for outer direction or counterclockwise
for inner direction to move the #2 variable range marker. The actual
target distance appears on the center top of the screen in selecting unit.
To turn off the #2 VRM, selects the FUNCTION-#2 VRM-OFF on the
menu sheet.
(4) Using cursor
Touch the JOYSTICK, cross cursor appears on the screen. The cross mark
will be move any direction by using the JOYSTICK and the range and bear-
ing Time-To-Go data and Lat/Loug of the cursor position will be displayed
on the lower right corner on the display.
The cross cursor and cursor data will disappear in approximately 15 sec-
onds.
4.12 BEARING MEASUREMENT
(1) Using the bearing scale
Using the bearing scale on the screen, visually estimate the bearing where
the radial line of the bearing scale would pass through the center of the
target. The bearing you obtain will be the target’s relative bearing in de-
grees.
(2) Using #1 EBL
Press the EBL/VRM key.
If VRM is highlighted, press and hold the EBL/VRM key to change to EBL
mode.
Rotate the J-DIAL clockwise or counterclockwise to move the electronic
bearing line to the center of the target. Target bearing appears on the center
top of the screen in degrees. Bearing may be displayed in relative “R”, true
“T”, or magnetic “M” depending on the menu selection.
To turn off the EBL, press the EBL/VRM key while EBL is highlighted.
(3) Using #2 EBL
Press the JOYSTICK.
Selects FUNCTION menu, then press the JOYSTICK.
Selects #2 EBL-SET, then press the JOYSTICK. The EBL2 appears high-
light on the upper right corner of the display.
Rotate the J-DIAL clockwise or counterclockwise to move the #2 EBL
OPERATION
31

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC Radar2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC Radar2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info