28360
22
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
15
3.7 INITIAL OPERATION AND CHECK OUT
3.7.1 INSPECTION AFTER THE INSTALLATION
After completing the installation and prior to energizing the equipment, it is
necessary to assure that all the steps of the installation were accomplished in
accordance with the instructions.
(1) The cables are not crimped or damaged.
(2) The input voltage connected accurately.
(3) The securing bolts of all equipment is tightened.
(4) The connection of the power cable shield is made properly to RF
ground.
3.7.2 OPERATING INITIAL SETTING MENU
Press the JOYSTICK, and the initial setting menu will be appear on the screen.
The JOYSTICK is used to select a particular menu. The particular menu will be
highlighted character, then press the JOYSTICK.
3.7.3 RELATIVE BEARING ALIGNMENT
This alignment should be made when the radar unit is installed. Failure to per-
form this procedure can result in incorrect target bearing readings.
Proceed as follows:
Identify a suitable targets (e.g. buoy, etc.) preferably between 0.5 and 1 NM
in range on the screen.
Visually locate the target and line the bow of the vessel up with the target.
Put the EBL marker on the target.
Press and hold the JOYSTICK for the initial setting menu.
Select BEARING by using the JOYSTICK, press the JOYSTICK for the
bearing adjustment mode.
INSTALLATION
15
3.7 INITIAL OPERATION AND CHECK OUT
3.7.1 INSPECTION AFTER THE INSTALLATION
After completing the installation and prior to energizing the equipment, it is
necessary to assure that all the steps of the installation were accomplished in
accordance with the instructions.
(1) The cables are not crimped or damaged.
(2) The input voltage connected accurately.
(3) The securing bolts of all equipment is tightened.
(4) The connection of the power cable shield is made properly to RF
ground.
3.7.2 OPERATING INITIAL SETTING MENU
Press the JOYSTICK, and the initial setting menu will be appear on the screen.
The JOYSTICK is used to select a particular menu. The particular menu will be
highlighted character, then press the JOYSTICK.
3.7.3 RELATIVE BEARING ALIGNMENT
This alignment should be made when the radar unit is installed. Failure to per-
form this procedure can result in incorrect target bearing readings.
Proceed as follows:
Identify a suitable targets (e.g. buoy, etc.) preferably between 0.5 and 1 NM
in range on the screen.
Visually locate the target and line the bow of the vessel up with the target.
Put the EBL marker on the target.
Press and hold the JOYSTICK for the initial setting menu.
Select BEARING by using the JOYSTICK, press the JOYSTICK for the
bearing adjustment mode.
INSTALLATION
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC Radar2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC Radar2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info