28360
18
Verklein
Vergroot
Pagina terug
1/54
Pagina verder
11
3.4 MOUNTING THE SCANNER UNIT
INSTALLATION
Selecting an adequate location for the scanner unit requires careful consider-
ation. On many small vessels, the unit can be installed on a mast platform, on
an arch, or on a bridge structure near the ship’s center line.
The radiator beam should not be obstructed by nearby large objects. Locate the
unit where large structures such as superstructures, searchlight, horns or masts
are not in the same horizontal plane, otherwise, blind areas and false targets can
appear on the radar screen.
Using the template provided in the front of manual as a guide, prepare the mount-
ing surface with the four mounting holes as required. Install the Radome and
secure it to the mounting surface. The correct mounting hardware is stainless
steel hexhead bolts
5
/16”, 1
1
/4long with 18 UNC thread. A flat and lock washers
should be used. The Radome should be parallel to the ship’s waterline and ori-
ented so the cable inlet is pointed AFT.
When mounting the Radome to a platform attached to a fly bridge, or super-
structure, avoid placing the Radome Unit at eye level. Although the radar trans-
mits a 2.0 kW peak power the average power radiated is less than 0.5 W. There-
fore, the hazard from RF radiation levels is virtually nonexistent beyond 2 feet
from the Radome Unit.
However, due to the sensitivity of the human eye, it is recommended and pru-
dent to install the Radome in a plane above or below the passengers line-of-
sight.
When the sickness of the mounting base is more than 0.4 inches, the longer
bolts are required. In this case, the bolts length is as follows;
Bolt length (inch) 1.25 + sickness of mounting base (inch)
If the longer bolts are used, the modulator PCB could potentially damaged.
When installing an aerial,make a hole for the water pulling-out.
The equipment sometimes becomes breaking cause because it is
flooded when getting a hole for the water pulling-out without
making it.
CAUTION
11
3.4 MOUNTING THE SCANNER UNIT
INSTALLATION
Selecting an adequate location for the scanner unit requires careful consider-
ation. On many small vessels, the unit can be installed on a mast platform, on
an arch, or on a bridge structure near the ship’s center line.
The radiator beam should not be obstructed by nearby large objects. Locate the
unit where large structures such as superstructures, searchlight, horns or masts
are not in the same horizontal plane, otherwise, blind areas and false targets can
appear on the radar screen.
Using the template provided in the front of manual as a guide, prepare the mount-
ing surface with the four mounting holes as required. Install the Radome and
secure it to the mounting surface. The correct mounting hardware is stainless
steel hexhead bolts
5
/16”, 1
1
/4long with 18 UNC thread. A flat and lock washers
should be used. The Radome should be parallel to the ship’s waterline and ori-
ented so the cable inlet is pointed AFT.
When mounting the Radome to a platform attached to a fly bridge, or super-
structure, avoid placing the Radome Unit at eye level. Although the radar trans-
mits a 2.0 kW peak power the average power radiated is less than 0.5 W. There-
fore, the hazard from RF radiation levels is virtually nonexistent beyond 2 feet
from the Radome Unit.
However, due to the sensitivity of the human eye, it is recommended and pru-
dent to install the Radome in a plane above or below the passengers line-of-
sight.
When the sickness of the mounting base is more than 0.4 inches, the longer
bolts are required. In this case, the bolts length is as follows;
Bolt length (inch) 1.25 + sickness of mounting base (inch)
If the longer bolts are used, the modulator PCB could potentially damaged.
When installing an aerial,make a hole for the water pulling-out.
The equipment sometimes becomes breaking cause because it is
flooded when getting a hole for the water pulling-out without
making it.
CAUTION
18

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC Radar2000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC Radar2000 in de taal/talen: Engels als bijlage per email.

De handleiding is 5,53 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info