28356
127
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
126
Section 6 Inter Switch (option)
Unit Connecting Cable
Be sure that the positive and negative polarity for the power connected to
both display units is the same.
It is necessary to connect the 12 V connector and GND connector to the
same terminal. The voltage is 12 V.
Also, the switchbox is not sealed against leaks, be sure to install it indoors
where it will not be splashed with seawater or liquids.
In the default setting (setting 2), the settings are made for display unit 1 to be
installed in the cabin, and display unit 2 to be installed in the upper bridge or a
similar place. (TB 1: Jumper between 1 - 2; TB 2: Jumper between 2 - 3)
The following setting example is written as if display unit 1 (the display unit
that is normally ON when under way) is in the cabin, and display unit 2 is
installed in the upper bridge or someplace similar.
(1) Connect both display unit 1 and display unit 2 to the J1 power cable, be
careful to connect each power cable as noted, connect the "RED" line to the
12 V power positive side, and in the same way connect the "BLACK" to the
negative.
(2) Connect the J2 of display unit 1 to the CFQ-6550 cable, connect one side to
the "MASTER (CABIN)" of NCZ-1432 (switchbox below).
(3) In the same way, connect the J2 of display unit 2 to one of the CFQ-6550
cables, connect one side to the "SLAVE (UPPER BRIDGE)" in the
switchbox.
(4) Connect cable CFQ-6531, which runs between the antenna and the display
unit, to "TO SCANNER" in the switchbox. At this time, cut off the black
waterproof cap with a razor knife or box cutter.
Read the following only if you are entering NMEA data for GPS or similar
kinds of receivers.
(5) Connect the cable from the GPS receiver (DGPS200 etc.) to the J3 (GPS) of
display unit 1.
(6) Connect the connectors attached to the display unit to the cables in the
following way, connect the J4 of display unit 1 to the J3 of display unit 2.
In this case, power to the GPS receiver is provided from display unit 1, and the
GPS receiver will not operate, and NMEA data will not be input, if display unit 1
is not turned ON.
1
2
3
4
5
1
2
3
4
5
J3 of display unit 1 J4 of display unit 2
Figure 6-2 NMEA cable connections
127

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC Radar1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC Radar1800 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info