28356
95
Verklein
Vergroot
Pagina terug
1/148
Pagina verder
94
Section 3 Operation
GPS SETTING
•In this item, you can perform the initial settings when JRC’s GPS/
DGPS sensor GPS112 or DGPS212 is connected to the RADAR
1800. The menu includes both basic settings and initial settings. The
basic settings reflect the general GPS/DGPS sensors and the initial
settings reflect the beacon module of the DGPS sensor. Before setting,
you need to set the clock built in the plotter using CLOCK ADJUST.
Note:
•Use TX COMMAND to send the values set in the following settings.
VESSEL POSITION (Setting the vessel position)
•In this menu, you can set your vessel’s current position. It will take
about 20 minutes to complete the positioning through the GPS/
DGPS when you turn the power on for the first time or after you
perform the master reset. You can save time, however, by setting your
vessel’s position, as well as time difference and antenna height
described below.
TIME DIFFERENCE (Setting the time difference)
•In this menu, you can set the time difference between UTC
(Universal Time Coordinate) and the local time.
ANTENNA HEIGHT (Setting the antenna height)
•In this menu, you can set the antenna height (from the sea level) of
the GPS/DGPS sensor.
GEODETIC DATUM (Setting a geodetic system)
•In this menu, you can set the data type of the Geodetic System the
GPS/DGPS sensor uses. In preparing charts or maps, cartographers
rely on a particular geodetic datum or scaling system (Geodetic
System) on which to calibrate the Latitude/Longitude coordinate
structure onto their charts. The GPS/DGPS sensor also calculates the
vessel’s position using the same Geodetic System. If the data type used
in the Geodetic System by cartographers and the GPS/DGPS differ,
the positions calculated by the GPS/DGPS may be considerably
different, up to 200 m, from those in the charts. Therefore, it is
necessary to set this item so that both sides use the same data type.
The data type used is normally listed in the margin on the chart. Set
the same data type.
There are 46 types of data available currently. (Refer to “Geodetic
System Table” p.140)
FIX MODE (Setting the fixing mode)
•In this menu, you can set the geodetic mode of the GPS/DGPS
sensor. When the GPS is connected, 3D provides more precise data
than 2D. When the DGPS212 is connected, the AUTO mode is
selected regardless of this setting.
GPS SETTING
N 0° 00.000'
E 0° 00.000'
+
00:00
0.0m
WGS-84
AUTO
10
2S
00 00 00
00 00 00
POSITION
TIME DIFF.
ANTENNA HEIGHT
GEODETIC DATUM
FIX MODE
HDOP LEVEL
AVERAGE
EXCLUDE SAT.
TX COMMAND
95

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC Radar1800 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC Radar1800 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,05 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info