28344
328
Verklein
Vergroot
Pagina terug
1/404
Pagina verder
A-10
APPENDI
X
3. REFERENCES
Preheating Time after Pattern Selection
After switching over the interswitch patterns, it is necessary to wait for the time as
mentioned below because the pre-heat time is different from the previous
interconnection between the MTR and the display unit. This measure is taken for
protecting the electronic tube emitting radar pulses.
(a) Not changed to the new interconnection condition:.........................No preheat
time
(b) Changed to the new interconnection condition.
However, the MTR was used before change:...........................................30
seconds
(c) Changed to the new interconnection condition.
However, the MTR was used before change:.............................................3
minutes
Notes on Pattern Selection
Immediately after switching over the patterns, the try to select another pattern may fail.
This means that even If the pattern switchover is completed, it takes some time to
prepare for the next interswitch operation. In this case, "ISW BUSY" will be indicated in
the message area on the display lower right, and the interswitch operation is not
available.
Alarm Sound Control
The interseitch alarm continues to sound for about 5 seconds. In setting the alarm sound
level, open the Sub1 Menu, press [2] switch to select the "5.BUZZER" in LEVEL Menu.
When stopping the alarm sound immediately after it sounds, press [ALARM ACK] switch.
Even when the alarm sound stops, a certain message will remain in the message area.
Notes on Master/Slave Connection
The Master/Slave connection is a configuration in which the Display Unit connected to the
Scanner Unit is the Master Unit, while the Display Unit connected to the Master Unit is a
Slave Unit. Of the interswitch patterns, the following pattern numbers includes the
Master/Slave connection:
a) 2-unit System: No.3, No.4, No.5 and No.6
b) 3-unit System: No.4, No.5, No.6, No.7, No.8, No.9, No.10 and No.11
If the Master Display Unit is not in the transmission state, it is impossible to set the Slave
Display Unit to the transmission state, If the Master Display Unit is changed from the
transmission to the standby mode, the Slave Display Unit will also be set to the standby
mode forcibly. In this status, "MTR ST-BY" will be indicated in the message area and the
alarm will beep.
328

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JRC JMA9923_7XA bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JRC JMA9923_7XA in de taal/talen: Engels als bijlage per email.

De handleiding is 7,69 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info