701310
5
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
SPEAKER OUTPUTS
The e4300’s speaker outputs are designed to
accept 8 AWG - 16 AWG wire.
Each pair of the e4300’s channels are designed
to deliver power into speaker loads equal to or
greater that 2 when using a “stereo” configuration
and speaker loads equal to or greater than 4
when using a “bridged” configuration.
Speaker loads below 2 nominal per channel
are not recommended and may cause the amplifier
to initiate a protection mode and shut itself off.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the output
of two amplifier channels to drive a single load.
When bridged, each channel produces signals of
equal magnitude, but opposite polarity.The
combined output of the two channels provides
twice the output voltage available from a single
channel.The e4300 has been designed for bridging
of its channel pairs without the need for input
inversion adaptors.
To bridge a pair of channels, use the “Left +” and
“Right –” speaker connectors only (the “Left –”
and “Right +” remain unused).When bridged, each
channel will deliver optimum power into a 4 load.
IMPORTANT
!
When a pair of channels are bridged, they will
deliver 150W x 1 into a 4 load or 90W x 1 into
an 8 load. Operating a pair of bridged channels
into a load lower than 4 is not recommended.
Because a bridged pair of channels requires that
both channels receive input, you need to connect
both left and right inputs to the source unit.
Connection of only one input will result in reduced
power output, increased distortion and can cause
the amplifier to overheat. Do not do this!
When a pair of the e4300’s channels are
operating in bridged mode, the output will be in
mono (only one channel).This mono channel can
contain right channel only information, left channel
only information or the sum of the information
from both the right and left channels. In order to
achieve one of these options, configure the inputs
to that pair of channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a Left-only or
Right-only signal to a pair of the e4300’s channels,
use a “Y-Adaptor” to split the single channel signal
into both left and right RCA inputs (or parallel-
connect both positive and both negative high-level
input connections to a single channel source signal).
This option is useful when using a pair of the
e4300’s channels to drive left channel speakers only
and the other pair of the e4300’s channels to drive
right channel speakers only.
When parallel-connecting both positive and both
negative high-level input connections as described
above, make sure to connect negative (–) wires to
negative (–) wires and positive (+) wires to
possitive (+) wires.
2) Left + Right Channel Information: When
bridged and fed by a stereo input, a pair of the
e4300’s channels will automatically combine the left
and right channels into a summed mono (left +
right) channel.This option is useful when using a pair
of the e4300’s channels to drive a subwoofer
system or a summed mono center channel.
IMPORTANT
!
IMPORTANT
!
JL AUDIO e4300 9
BASS BOOST CONTROLS
1) CH 3&4 Bass Boost: This switch allows the
user to activate a 6 dB boost centered at 48 Hz for
channels 3&4.When the “CH 3&4 Bass Boost” is
activated, the inputs to “CH 3 (Left)” and “CH 4
(Right)” are summed to create a mono signal.The
“Filter Mode” switch in the “Channel 3 & 4” section
must be in the “LP” position for the bass boost to
be functional.
2) Remote Bass Port: This port allows you to
connect an optional remote boost knob (sold
separately, JL Audio Model RBC-1) that can be
mounted in the front of the vehicle. With the
RBC-1 connected, the boost is no longer limited to
0 or +6 dB, allowing a range of 0 - 12 dB of boost
to be selected.
PRE-OUTS
The e4300’s “Pre-Outs” connectors output
unprocessed (pass-through) left and right channel
preamp level signals, permitting connection of
additional amplifiers in a system.This pass-through
pre-amp output can be configured two different ways
using the switch labeled “Pre-Outs Input From”.
1) “1&2”: In this mode, the preamp output
delivers the same signal that is connected to the
e4300's “CH 1 (Left)” and “CH 2 (Right)” Inputs.
This mode is useful for feeding a subwoofer
amplifier when the e4300 is being used to drive
front and rear speaker systems.This preamp
output mode will track the signal level of
channels 1&2, allowing fading of the rear channels
without affecting the subwoofer level.
2) “Sum”: This mode sends a sum of the channels
1 & 3 input signals to the left pre-out connector and
a sum of the channels 2 & 4 input signals to the right
pre-out connector.This signal is not affected by the
“CH 3&4 Bass Boost” processing selected for the
amplifier or by any crossover filter selected.When the
e4300 is being used to drive front and rear speaker
systems, this preamp output mode will deliver a
summed front/rear signal to the subwoofer amplifier,
while permitting fading of the front and rear speaker
systems from the source unit.
When using either the line level inputs (RCA
input connections) or the “High Level Inputs”
(four-pin connector), the output signals are identical
to the input signals. If the “High Level Inputs” are
used, the signal present at the “Pre-Outs” can still
be sent to another JL Audio amplifier. In either case,
the “Pre-Outs” signals are not affected by any
settings in the “Amplifier Controls” or “CH 3&4
Bass Boost” sections.
8 JL AUDIO e4300
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio e4300 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio e4300 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,32 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info