700450
4
Verklein
Vergroot
Pagina terug
1/41
Pagina verder
6 | JL Audio - XD1200/1v2 Owners Manual
7
ENGLISH
In signal and DC sensing applications, the
amplifier’s Remote” turn-on terminal becomes
a remote turn-on output. This allows the
XD1000/1v2 to turn on other amplifiers in the
audio system that do not have signal sensing.
INPUT SECTION
The XD1000/1v2 employs a differential-
balanced input topology that provides the user
with a high degree of input flexibility, while
retaining superior noise rejection. This type of
circuit also allows the XD1000/1v2 to accept high-
voltage inputs from factory source unit outputs
without excessive distortion or noise problems.
You may run a stereo or a mono signal into
the inputs of the amplifier. The amplifier’s input
section automatically sums stereo signals to mono
for the internal amplifier section. The amplifier
will operate with only one input connection
but will require an increase in input sensitivity
to overcome the loss of signal. If a mono input
signal is to be run, we recommend that you use
a “Y-adaptor” to split the mono signal into both
inputs of the amplifier. If you are feeding only
one input and using either the DC-Offset or
Signal Sensing “Turn-On Mode,” you must use
the left-channel input for the automatic turn-on
to operate.
Input Voltage Range:
Input Voltage Range: A wide range of signal
input voltages can be accommodated by the
XD1000/1v2’s input section (200mV – 8V).
This wide range is split up into two sub-ranges,
accessible via the “Input Voltage” switch:
Low: for preamp level signals
High: for speaker level signals
The “Lowposition on the “Input Voltage
switch selects an input sensitivity range between
200mV and 2V. This means that the “Input Sens.
rotary control will operate within that voltage
window. If you are using an aftermarket source
unit, with conventional preamp level outputs, this
is the position you should select.
The “High” position on the “Input Voltage
switch selects an input sensitivity range between
800mV and 8V. This is useful for certain high-
output preamp level signals as well as speaker
level output from source units and small
amplifiers. To use speaker level sources, splice the
speaker output wires of the source unit or small
amplifier onto a pair of RCA cables or plugs,
or use the JL Audio ECS Speaker Wire to RCA
adaptor (XD-CLRAIC2-SW).
Line Output Converters are usually not needed
with the XD1000/1v2. If you find that the output
cannot be reduced sufficiently with a direct
speaker level signal applied to the amplifier and
the “Input Voltage switch in its “High” position,
you may use a Line Output Converter or voltage
divider to reduce the signal level.
TURNON OPTIONS
The XD1000/1v2 can be switched on and off
using one of three methods, determined by the
position of the amplifier’s “Turn-On Mode
switch. Please read these options and decide
which is best suited for your specific system.
1) +12V remote turn-on lead (preferred)
2) Signal-sensing turn-on circuit
3) DC offset-sensing turn-on circuit
+12 V Remote Turn-On: This is the preferred
method for turning the amplifier on/off. The
amplifier will turn on when +12 V is present at
its Remote” input and turn off when +12 V is
switched off. This +12 V remote turn-on signal is
typically controlled by a source unit's remote
turn-on wire. The XD1000/1v2’s Remote” turn-
on connector will accept 18 AWG – 12 AWG
wire. To connect the remote turn-on wire to
the amplifier, first back out the set screw on the
top of the terminal block, using the supplied 2.5
mm hex wrench. Strip 1/2 inch (12mm) of wire
and insert the bare wire into the terminal block,
seating it firmly so that no bare wire is exposed.
While holding the wire in the terminal, tighten
the set screw firmly, taking care not to strip the
head of the screw and making sure that the wire
is firmly gripped by the set screw.
If a source unit does not have a dedicated
remote turn-on output, consider one of the
following alternative turn-on options:
These methods are useful when a conventional
+12 V remote turn-on signal is not available in a
system. These allow you to operate the amplifier
without having to locate a remote turn-on lead at
the source unit, which can be very useful when
interfacing the amplifier with OEM (factory)
audio systems that do not use conventional +12 V
turn-on leads.
Depending on the characteristics of the audio
signal, one of the following methods may work
better than the other. We recommend trying DC
Offset-Sensing first as it does not require a long
delay to turn the system off after the signal is
shut off.
DC Offset-Sensing: The amplifier will turn on
and off by detecting the presence of a very small
DC signal (offset) that is typical in the audio
output of most OEM (factory) source units and
amplifiers. The amplifier will turn on and off in
reaction to the presence or absence of this DC
Offset. The sensitivity of this circuit is designed
for high-level (speaker level) signals, not for low-
level (preamp level) signals. The circuit senses the
left-channel signal only.
Signal-Sensing: The amplifier will turn on and
off by detecting the presence of a full-range
audio signal at its left-channel input. After
approximately 30 seconds, the amplifier will shut
off. The sensitivity of this circuit is designed for
high-level (speaker level) signals, not for low-level
(preamp level) signals. The circuit is tuned to
react to signals at mid-range frequencies. This
prevents false switching from signals created by
moving loudspeakers that are in parallel with the
amplifier’s input signal.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio XD1000 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio XD1000 in de taal/talen: Engels als bijlage per email.

De handleiding is 4,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info