700490
4
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
6 | JL Audio - MHD600/4 Owners Manual
7
Ground Connection
The ground connection should be made using
the same gauge wire as the power connection.
It is common for the alternator to be grounded
through its chassis. If the alternator is not
grounded through its chassis and instead employs
a small (10 AWG - 6 AWG) wire to connect to
ground, this wire should also be upgraded to 4
AWG when installing amplifier systems with main
fuse ratings above 60A.
Many vessels employ small (10 AWG - 6 AWG)
wire to connect the alternators positive
connection to the battery. To prevent voltage
drops, these wires should be upgraded to 4
AWG pure copper wire when installing amplifier
systems with main fuse ratings above 60A.
Turn-On Wire
The MHD600/4 uses a conventional +12V
remote turn-on wire, typically controlled by
the source units remote turn-on output. The
amplifier will turn on when +12V is present at
its Remoteinput and turn off when +12V is
switched off. If a source unit does not have a
dedicated remote turn-on output, the amplifier’s
turn-on lead can be connected to +12V via a
switch that derives power from an ignition-
switched circuit.
The MHD600/4’s Remote turn-on connector
is designed to accept 18 AWG – 12 AWG wire. 18
AWG is more than adequate for this purpose.
To connect the remote turn-on wire to the
amplifier, first back out the set screw on the
bottom of the Power Connector Plug, using the
supplied hex wrench. Strip 1/2 inch (12mm) of
wire and insert the bare wire into the receptacle,
seating it firmly so that no bare wire is exposed.
When using smaller wire, it may be necessary to
strip 1 inch of insulation from the wire and fold
the bare wire in half prior to insertion. While
holding the wire in the terminal, tighten the
set screw firmly using the supplied 2.5 mm hex
wrench, taking care not to strip the head of the
screw and making sure that the wire is firmly
gripped by the set screw.
Amplifier Power Connector Plug
To connect the power wires and the remote
turn-on wire to the amplifier, unplug the power
connector plug from the amplifier chassis (pull
back firmly) and back out the set screws on
the connector plug, using the supplied 4 mm
hex wrench for the +12 VDC and Ground
connections and the supplied 2.5 mm hex wrench
for the Remoteconnection. Strip 3/8 inch (10
mm) of insulation from the end of each wire and
insert the bare wire into the receptacle on power
connector plug, seating it firmly so that no bare
wire is exposed. While holding each wire in place,
tighten each set screw firmly, taking care not to
strip the head of the screw.
Never make power connections with a “live”
wire. Always disconnect the negative battery
post before making any connections or
adjustments to a 12V power connection!
POWER AND TURNON CONNECTIONS
Before installing the amplifier, disconnect the
negative (ground) wire from the vessels battery.
This will prevent accidental damage to the system,
the vessel and your body during installation.
Rear Preouts
Remote
Level
Control
Front
Inputs
L
R
L
R
+12 VDC Ground Remote
+12V Battery Connection
You will need to connect a power wire to
the vessels positive battery terminal, using an
appropriate power ring or specialized battery
terminal connector, such as the JL Audio
XB-BTU. This connection must be tight and
corrosion-free to ensure proper connectivity.
This wire MUST be fused appropriately for safety.
Any positive power wires run through barriers
must be protected with a high quality insulating
grommet to prevent damage to the insulation
of the wire. Failure to do so may result in a
dangerous short circuit.
Power Wire Requirements
The MHD600/4’s +12 VDC and Ground
connections are designed to accept 4 AWG power
wire. 4 AWG pure copper wire is recommended
for any power wire run longer than 72 inches (180
cm). For runs shorter than 72 inches, 8 AWG pure
copper power wire is acceptable.
If you are installing the MHD600/4 with other
amplifiers and wish to use a single main power
wire, use 2 AWG or 1/0 AWG pure copper wire
as a main power wire. This 2 AWG or 1/0 AWG
power wire should terminate into a distribution
block mounted as close to the amplifiers as
possible and should connect to the MHD600/4
with 4 AWG or 8 AWG pure copper power wire.
Please note that lower AWG numbers mean
bigger wire and vice-versa (1/0 AWG is the largest,
2 AWG is smaller, then 4 AWG, then 8 AWG, etc.).
We do not recommend the use of “copper-
clad aluminum wire” or “CCA” wire because
this wire is significantly less conductive than
pure copper wire. Only use pure copper power
wire, such as JL Audio’s MetaWire™. Tinned
copper wire (silver color) is acceptable as the
tin-plating is only a very minor component of
the wire.
Fuse Requirements
The installation of a fuse on the main power
wire, within 18 wire inches (45 cm) of the positive
battery terminal is vital to protect the wire and
the vehicle from fire in the event of a collision
or short-circuit. The fuse value at each power
wire should be just high enough for all of the
equipment being run from that power wire. Do
not use a fuse with a value that far exceeds the
total fuse rating of the electronics connected to
the wire.
If only the MHD600/4 is being run from
that power wire, we recommend a 50A fuse
be used. AGU (big glass fuse). AFS (small
blade fuse) or MaxiFuse™ (big plastic-
body fuse) types are recommended.
If other amplifiers are also being powered from
a main power wire and exceed 80 amps in total
fuse rating, we recommend the use of an ANL
(large-blade) fuse and holder. Each amplifier can
then be fused independently at the outputs of
the power distribution block. Use JL Audio part
XC-FOA-2PAK and appropriate MaxiFuse™ type
fuses with JL Audio distribution blocks.
Please consult with your JL Audio
dealer to make sure that the wire, fuse
holder and fuse ratings are appropriate
for your system’s needs. The safety of
your installation depends on appropriate
power connections and fuse protection.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio MHD600 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio MHD600 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van JL Audio MHD600

JL Audio MHD600 Gebruiksaanwijzing - English - 24 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info