701315
5
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
8 JL Audio
9
PREAMP OUTPUTS
The J2-360.2 incorporates a pass-through
preamp output section, so that additional
amplifiers can be easily added to the system. This
pass-through pre-amp output delivers the same
signals that are fed into the amplifier's inputs.
Filter Frequency (Hz)Input Sens. Bass Boost
min max
50 500 O +9dB
Power Protect
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
HP
|
Off
|
LP
Filter Mode
High-Level Inputs
The preamp output signal is not affected by the
Bass Boost processing selected for the amplifier
or by any crossover filter selected (if the input
signal is full-range, the preamp output will be
full-range).
Note: The signal level of the Preamp Output is
always line-level (low voltage).
SPEAKER OUTPUTS
The J2-360.2’s speaker outputs are designed to
accept 16 AWG - 8 AWG wire.
Made in China
LEFT CHANNEL RIGHT CHANNEL
Bridged
FUSESGround
20A20A
Remote+ 12VDC
J2-360.2 is designed to deliver power into
speaker loads equal to or greater than 2 ohms per
channel when using a “stereo” configuration and
speaker loads equal to or greater than 4 ohms
when using a “bridged” configuration.
IMPORTANT
!
Speaker loads below 2 ohms nominal per
channel are not recommended and may cause
the amplifier to initiate a protection mode.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from
a single channel. The J2-360.2 has been designed
for bridging of its channels without the need for
input inversion adaptors.
To bridge a pair of channels, use the
Left +” and Right – speaker connectors only
(the Left – and Right + remain unused).
When bridged, the amplifier will deliver
optimum power into a 4 ohm load.
FILTER CONTROLS
The active filter built into the J2-360.2 can
be used to eliminate potentially harmful and/
or undesired frequencies from making their way
through the amplifier section to the speaker(s).
This serves to improve tonal balance and to avoid
distortion and possible speaker failure. Correct
use of this filter can substantially increase the
longevity and fidelity of your audio system.
Filter Frequency (Hz)Input Sens. Bass Boost
min max
50 500 O +9dB
Power Protect
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
HP
|
Off
|
LP
Filter Mode
High-Level Inputs
1) “Filter Mode” Control: The J2-360.2 employs
a 12dB per octave filter. This filter can be
configured into one of two filter types or
defeated completely by way of the three-
position Filter Mode switch:
“HP” (High-Pass): Configures the filter to
attenuate frequencies below the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of component speakers
the J2-360.2’s in a bi-amplified system.
Off”: Defeats the filter completely, allowing the
full range of frequencies present at the inputs
to feed the amplifier. This is useful for systems
utilizing outboard crossovers or requiring full-
range reproduction from the J2-360.2.
LP (Low-Pass): Configures the filter to
attenuate frequencies above the selected filter
frequency at a rate of 12dB per octave. This is
useful for connection of subwoofer(s) to the
J2-360.2’s in a bi-amplified system.
2) “Filter Freq. (Hz) The J2-360.2 has separate
Filter Frequency controls in each Channel
Controls section for the low-pass filter and
the high-pass filter. You will only use one of
these in each channel section, depending on
which “Filter Mode” you have selected (or
none of them if you have selected the “Off
position for the “Filter Mode”).
When active, the filter in the J2-360.2 is fully
variable between 50 Hz and 500 Hz via the
control knob labeled Filter Frequency (Hz).
The “9 o’clock” position corresponds to 80 Hz
and is a good starting point for system tuning.
“BASS BOOST” CONTROLS
Each channel pair of the J2-360.2 includes a
single band, boost-only bass equalizer controlled
by a rotary knob marked Bass Boost.
This control has a boost range of 0dB (full-
counterclockwise) to +9dB (full-clockwise) and is
centered at 45 Hz.
Filter Frequency (Hz)Input Sens. Bass Boost
min max
50 500 O +9dB
Power Protect
LEFT
RIGHT
LEFT
RIGHT
Preamp
Outputs
Amplifier
Inputs
HP
|
Off
|
LP
Filter Mode
High-Level Inputs
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio J 360 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio J 360 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,48 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info