701297
5
Verklein
Vergroot
Pagina terug
1/11
Pagina verder
When a pair of channels are bridged, they
will deliver 250W x 1 into a 4 ohm load or
160W x 1 into an 8 ohm load. Operating a
pair of bridged channels into a load lower
than 4 ohms is not recommended.
Because a bridged pair of channels requires that
both channels receive input, you need to
connect both left and right inputs to the source
unit. Connection of only one input will result in
reduced power output, increased distortion and
can cause the amplifier to overheat.
Do not do this!
When the G2250 operating in bridged mode,
the output will be in mono (only one channel).
This mono channel can contain right channel
only information, left channel only information
or the sum of the information from both the
right and left channels. In order to achieve one of
these options, configure the inputs to that pair of
channels in one of these two ways:
1) Left Channel Only or Right Channel Only
Information: If you wish to send a left-only or
right-only signal the G2250, use a “Y-Adaptor
to split the single channel signal into both left
and right RCA inputs. This option is useful
when using one G2250 to drive left channel
speakers only and the other G2250’s channels
to drive right channel speakers only.
2) Left + Right Channel Information:
When bridged and fed by a stereo input, the
G2250’s channels will automatically combine
the left and right channels into a summed
mono (left + right) channel. This option is
useful when using the G2250 channels to
drive a subwoofer system or a summed mono
center channel.
AMPLIFIER STATUS INDICATOR LIGHTS &
PROTECTION CIRCUITRY
There are two status indicator lights on the
input / control end of the amplifier.
1) “Power” (Green): lights to indicate that the
amplifier is turned on and operating normally.
2) “Protect” (Red): Indicates that the amplifier
protection circuitry has been activated to
prevent product failure due to a short-circuit
or a dangerously low impedance connected
to the amplifier output(s). Connecting the
speaker outputs to an impedance lower than
2 ohms stereo (4 ohms bridged) will cause
this protection mode to activate. When this
protection mode is activated, the amplifier will
reduce it maximum power output to protect its
circuitry, which will manifest itself as increased
distortion. When the problem is corrected, the
amplifier will return to normal operation.
Advanced Rollback Thermal protection
Unlike conventional thermal protection
systems, which shut down an amplifier when it
overheats, this system protects the amplifier by
gradually reducing power output if the amplifier’s
safe operating temperature is exceeded. The
amplifier will continue to operate and return
to normal power output once its temperature
returns to a normal range.
BASS BOOST CONTROLS
1) “Bass Boost: This switch allows the user to
activate a 6 dB boost centered at 48 Hz.
When the Bass Boost is activated, the inputs
to CH 1 (Left) and CH 2 (Right) are
summed to create a mono signal. The Filter
Mode switch in the Channel 1 & 2 section
must be in the LP position for the bass boost
to be functional.
2) Remote Bass Port: This port allows you to
connect an optional remote boost knob (sold
separately as JL Audio Model RBC-1) that can
be mounted in the front of the vehicle. With
the RBC-1 connected, the boost is no longer
limited to 0 or +6 dB, allowing a variable
range of 0 to +12 dB of boost to be selected.
PREOUTS
The G2250 incorporates a pass-through
preamp output section, so that additional
amplifiers can be easily added to the system. The
preamp output delivers the same signals that are
connected to the G2250’s inputs.
The preamp output signals are not affected
by the Bass Boost” processing selected for the
amplifier or by any crossover filter selected (if the
input signals are full-range, the preamp output
will be full-range).
The signal level of the Preamp Output” is
line-level (low voltage), regardless of the position
selected in the G2250’s “Input Voltage” switch.
An additional amplifier connected to these
preamp outputs should have its input voltage
switch set to the “Low” position.
SPEAKER OUTPUTS
The G2250’s speaker outputs are designed to
accept 16 AWG - 8 AWG wire.
The G2250 is designed to deliver power into
speaker loads equal to or greater than 2 ohms
when using a “stereo” configuration and speaker
loads equal to or greater than 4 ohms when using
a “bridged” configuration.
Speaker loads below 2 ohms nominal per
channel in stereo or below 4 ohms nominal
bridged mono are not recommended and may
cause the amplifier to initiate a protection
mode which reduces power output.
BRIDGING CONSIDERATIONS
Bridging is the practice of combining the
output of two amplifier channels to drive a single
load. When bridged, each channel produces
signals of equal magnitude, but opposite polarity.
The combined output of the two channels
provides twice the output voltage available from
a single channel. The G2250 has been designed
for bridging of its channels without the need for
input inversion adaptors.
To bridge the G2250’s two channels, use the
CHANNEL 1 + and CHANNEL 2 –
speaker connectors only (the CHANNEL 1 –
and CHANNEL 2 + remain unused). When
bridged, the G2250 will deliver optimum power
into a 4 ohm load.
8 JL AUDIO G2250 JL AUDIO G2250 9
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio G2250 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio G2250 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,61 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info