701229
5
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
C7-100ct: Installation
PROTECTION CAPACITOR
A high-quality 15μF protection capacitor is
included with the C7-100ct to guard against damage
from transient electrical pops (turn-on/off). This
capacitor is not a substitute for high-pass filtering
and must be connected in all installations. The
capacitors value has been selected so as not to
interfere with a properly set active high-pass filter.
The protection capacitor supplied with your
C7-100ct should be installed in a dry location and
as near as possible to the tweeter. Connect the
protection capacitor in-line (series) with the tweeter’s
positive (+) lead, as shown in Diagram A below. The
capacitor is bipolar and may be connected in either
direction. Make sure to insulate the capacitor’s leads
to guard from touching against any exposed metal.
Use plastic cable ties or a similar fastener to securely
mount the capacitor to avoid coming loose in the
event of a collision, sudden jolt or repeated vibrations
during normal use. Make sure that your mounting
location will not cause damage to wiring or any other
vital component of your vehicle.
TWEETER CONNECTIONS
Run the wire leads from the tweeter mounting
locations to the amplifier outputs. Then connect the
harness wire leads to the speaker/amplifier outputs
and tweeters, observing correct polarity. See
Diagram A below for details.
WARNING
!!
It is absolutely vital that the protection capacitor
is connected, as shown in Diagram A. Failure to
connect the protection capicitor as shown will result
in damage which is NOT covered under warranty.
TWEETER INSTALLATION
C7 tweeters have been designed for surface or
flush-mounting. Before choosing a method, carefully
inspect the desired mounting location to determine
which method will work best.
Surface-Mount: uses the supplied surface-
mount fixture and requires the drilling of three
holes (two for the wires and one for the mounting
screw). This application is useful when mounting the
tweeters to a panel that has insufficient clearance
behind it for the tweeter’s magnet structure.
Flush-Mount: yields a custom-installed
appearance and requires a 1.88-inch (48 mm)
diameter hole to be cut in the vehicle panel. At least
1.75-inch (44 mm) of clearance is required behind
the tweeter mounting surface for the spring clip and
1-inch machine screw used to mount the fixture.
In limited depth applications, it may be necessary
to cut down the length of the machine screw, or to
use a shorter screw (not supplied). Hand-tighten the
machine screw until the fixture is secure, as shown
in Diagram C.
From Amplier
Tweeter
Diagram A:
Tweeter / Protection Capacitor Wiring
5
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio C7-100ct bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio C7-100ct in de taal/talen: Engels als bijlage per email.

De handleiding is 2,26 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info