701251
5
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
5
TWEETER INSTALLATION
C1 tweeters have been designed for surface
or flush-mounting. Before choosing a method,
carefully inspect the desired mounting location
to determine which method will work best.
Surface-Mount: uses the supplied surface-mount
fixture and requires the drilling of three holes (one
for the wires and two for the mounting screws). This
application is useful when mounting the tweeters to a
panel that has insufficient clearance behind it for the
tweeter’s magnet structure.
Flush-Mount: yields a custom-installed appear-
ance and requires a 1-1/2-inch (38 mm) diameter hole
to be cut in the vehicle panel, with at least 0.40-inch
(10 mm) of clearance behind the mounting surface
for the tweeter and up to 1.45-inch (37 mm) for the
stud bolts used to mount each tweeter.
TWEETER PROTECTION
The C1 crossover networks are equipped with
an advanced electronic tweeter protection circuit
designed to minimize the possibility of tweeter
failure. This electronic device monitors current going
to the tweeter and will disconnect the tweeter from
the signal when it senses overload. Should this occur
while listening to the audio system, simply reduce the
volume for a few seconds and the protection circuit
will reset itself automatically.
CROSSOVER NETWORK INSTALLATION
The crossover networks supplied with your C1
System should be installed in a dry location inside
your vehicle. DO NOT INSTALL THEM INSIDE
OF A DOOR! Doors often get wet on the inside,
which can damage your crossover networks and
could potentially damage your entire sound system.
Use plastic cable ties or a similar fastener to securely
mount each crossover to avoid coming loose in the
event of a collision, sudden jolt or repeated vibrations
during normal use. Make sure that your mounting
location will not cause damage to wiring or any other
vital component of your vehicle.
TWEETER CONNECTIONS
Run the wire leads from the crossovers to
the tweeter mounting locations and to the
speaker/amplifier outputs. Then connect the
harness wire leads to the speaker/amplifier
outputs and tweeters, observing correct
polarity. See Diagram C below for details.
WARNING
!!
It is absolutely vital that your component tweeter
is connected, as shown in Diagram C. Failure to
connect the tweeter as shown will result in damage
which is NOT covered under warranty. Only use
in-line filters clearly marked “C1-100cthp”.
Fr
om Woofer
or Amplier
Tweeter Crossover
Tweeter
DIAGRAM C:
Tweeter / Crossover Wiring
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio C1-690 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio C1-690 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,67 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info