700441
5
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
8 | JL Audio - HD900/5 Owners Manual
9
AMPLIFIER INPUTS
The HD900/5 has three separate input sections,
one for the “Front” left and right channels,
another for the “Rear” left and right channels
and one for the Subwoofer Channel. Each section
consists of a pair of RCA-type input jacks on
the Connection Panel of the amplifier and input
controls on the Control Panel of the amplifier: a
single “Input Voltage” switch, an “Input Mode”
switch and three individual “Input Sens.” rotary
controls (one in each channel section).
“INPUT MODE” SWITCH
The Input Mode switch is located under
the “General Setup heading at the far right of
the control panel. This switch allows operation
of all five amplifier channels with only one pair
of input signals (2 ch.) or with independent front
and rear input signal pairs (4 ch.) or with discrete
front, rear and subwoofer signal pairs (6 ch.).
“6 Ch.” Input Mode
In this mode, you will connect separate pairs
of input cables to the “Front”, “Rear” and “Sub”
amplifier inputs, allowing you full channel
control from the source unit. If the source unit
only provides a mono (single) subwoofer output,
use a y-adaptor cable to feed both the Left” and
“Right subwoofer inputs of the HD900/5 with
the mono signal. Failure to do so will result in
reduced gain and possible distortion.
“4 Ch. Input Mode
In this mode, you will connect separate
pairs of input cables to the “Front and “Rear”
amplifier inputs and leave the Sub” inputs
unused. The subwoofer channels will receive
signal from the sum of the signals at the “Front”
and “Rear” inputs so that front-to-rear fading of
the main channels does not significantly affect
the subwoofer level.
“2 Ch.” Input Mode
To operate all five channels of the HD900/5
with a single pair of stereo inputs, select the
2 Ch. position on the Input Mode switch
and connect a single pair of input cables to
the “Front” input jacks only. The “Rear
and “Sub” input jacks will remain unused.
In this mode, the amplifier will route the
signals connected to the “Front inputs to
the Front, Rear and Subwoofer channels.
Front-to-rear fading will not be available.
“Input Voltage” Switch
A wide range of signal input voltages can be
accommodated by each of the HD900/5s differential-
balanced inputs (200mV – 8V RMS). This wide range
is split up into two sub-ranges, accessible via the
Input Voltage switch located next to the “Input
Mode switch under the “General Setup” heading.
The Low position of the Input Voltage
switch selects an input sensitivity range between
200mV and 2V for all the amplifier channels. This
means that the Input Sens. rotary controls will
operate within that voltage window. If you are
using an aftermarket source unit, with preamp-
level outputs, this is most likely the position that
you will use (regardless of what voltage output
capability is claimed by the source unit).
The High position of the Input Voltage
switch selects an input sensitivity range between
800mV and 8V. This is for use with speaker-level
outputs from source units and small amplifiers
found in many OEM (factory-installed) systems.
To use speaker-level sources, splice the speaker
output wires of the source unit or small amplifier
onto a pair of RCA plugs for each input pair or use
the JL Audio ECS Speaker Wire to RCA adaptor
(XB-CLRAIC2-SW). It is not necessary (or advisable)
to use “Line Output Converters” with
your HD900/5.
AMPLIFIER MOUNTING OPTIONS
The HD900/5 has two mounting options to
ease in installation.
Standard Mounting
The standard method of mounting requires
removal of the four corner caps with the 4 mm
hex wrench included with your amplifier. Using
appropriate mounting screws (not included),
secure the amplifier in all four corners and
replace the corner caps to cover the screws.
Lateral Mounting Feet
Lateral Mounting Feet are also included with
your HD900/5 to provide an alternative mounting
option. Each mounting foot should be attached
to the bottom of the amplifier by screwing the
provided bolt into the bottom of the amplifier and
up into the corner cap with the supplied 2.5 mm
hex wrench. Next, using appropriate mounting
screws (not included), secure the amplifier by its
four Lateral Mounting Feet.
Check before drilling any holes in your vehicle
to make sure that you will not be drilling
through a gas tank, brake line, wiring harness
or other vital vehicle system.
CONTROL PANEL SECURITY COVER
The HD900/5 features a Control Panel
Security Cover. When installed, the cover ensures
that your amplifier settings are not accidentally
changed while creating a clean aesthetic for the
amplifier and your installation. The control panel
security cover is pre-installed at the factory and
must be temporarily removed for access to the
controls described throughout this manual.
The security cover is secured by a single 2.5
mm hex-head screw at the far right of the panel.
Loosen the hex-head screw to release the security
cover (it is not necessary to completely remove the
screw). To re-install the security cover once all
adjustments have been made, insert the tongue on
the cover’s left edge into the groove where the left-
side heatsink meets the control panel, hinge the
panel closed and secure the screw using the
supplied 2.5 mm hex wrench. Do not overtighten
the screw.
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio 5 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio 5 in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info