700471
7
Verklein
Vergroot
Pagina terug
1/37
Pagina verder
12 JL Audio JX250/1 • JX500/1D • JX1000/1D 13
ENGLISH
JX500/1D Specifications:
Amplifier Topology: Class D
Power Supply: Unregulated PWM switching type
Frequency Response: 10 - 150 Hz (+0/– 1 dB)
Signal to Noise Ratio:
>62 dBA referred to highest rated power, >35 dBA
referred to 1W (20 Hz - 20 kHz noise bandwidth)
Damping Factor: >1000 @ 4 ohms
THD + Noise @ Rated Power: 1 %
Rated Continuous (RMS) Power @ 14.4V:
300W RMS x 1 @ 4
400W RMS x 1 @ 3
500W RMS x 1 @ 2
Rated Continuous (RMS) Power @ 12.5V:
235W RMS x 1 @ 4
300W RMS x 1 @ 3
410W RMS x 1 @ 2
Recommended Fuse Value (Type): 50A (MAXI or AGU)
Minimum Copper Power/Ground Wire Gauge: 4 AWG
Dimensions (LxWxH):
7.83" x 7.68" x 2.15" (199 mm x 195 mm x 53 mm)
Net Weight: 4.8 lbs. (2.18 kg)
JX1000/1D Specifications:
Amplifier Topology: Class D
Power Supply: Unregulated PWM switching type
Frequency Response: 20 - 150 Hz (+/– 1 dB)
Signal to Noise Ratio:
>75 dBA referred to highest rated power, >45 dBA referred
to 1W (20 Hz - 20 kHz noise bandwidth)
Damping Factor: >1000 @ 4 ohms
THD + Noise @ Rated Power: 1 %
Rated Continuous (RMS) Power @ 14.4V:
500W RMS x 1 @ 4
750W RMS x 1 @ 3
1000W RMS x 1 @ 2
Rated Continuous (RMS) Power @ 12.5V:
500W RMS x 1 @ 4
700W RMS x 1 @ 3
900W RMS x 1 @ 2
Recommended Fuse Value (Type): 80A (MAXI or ANL)
Minimum Copper Power/Ground Wire Gauge: 4 AWG
Dimensions (LxWxH):
10.94" x 7.68" x 2.09" (278 mm x 195 mm x 53 mm)
Net Weight: 7.0 lbs. (3.18 kg)
APPENDIX A:
Input Sensitivity Level Setting
Following the directions below will allow the
installer to adjust the input sensitivity of each
amplifier channel pair simply and easily in just a
few minutes using equipment which is commonly
available in installation bays.
Necessary Equipment
• Digital AC Voltmeter
CD with a sine-wave test tone recorded at
0 dB reference level in the frequency range
to be amplified (50 Hz is a good choice). Do not
use attenuated test tones (-10 dB, -20 dB, etc.).
The Nine-Step Procedure
1) Disconnect the subwoofer(s) from the
amplifier’s subwoofer output connector (you
need only disconnect Pos. or Neg., not both).
2) Turn off all processing (bass/treble, loudness,
EQ, etc.) on the source unit, processors (if
used) and amplifier. Set the source unit's fader
control to center position and its subwoofer level
control to 3/4 of maximum. If connected, set the
amplifier’s Remote Level Control at maximum
(full clockwise).
3) Turn the amplifier's “Input Sens.” control all
the way down.
4) Set the source unit volume to 3/4 of full
volume. This will allow for reasonable gain
overlap with moderate clipping at full volume.
5) Using the charts on this page, determine the
target voltage for input sensitivity adjustment
according to the nominal impedance of the
speaker system connected to the amplifier
outputs. Make sure you reference the appropriate
chart for your specific JX monoblock model.
6) Verify that you have disconnected the speakers
before proceeding. Play a track with an
appropriate sine wave (50 Hz is recommended)
at 3/4 source unit volume.
7) Connect the AC voltmeter to the speaker output
connectors of the amplifier. Make sure you test
the voltage at the correct connectors (+ and –).
8) Increase the Input Sens. control until the
target voltage is observed with the voltmeter.
9) Once you have adjusted the amplifier to
its maximum low-distortion output level,
reconnect the speaker(s) and listen to the
system. The Input Sens.” controls can
now be adjusted downward if the amplifier
requires attenuation to achieve the desired
system balance.
IMPORTANT!
!
Do not increase any Input Sens. setting for
any amplifier channel or channel pair in the
system beyond the maximum level established
during this procedure. Doing so will result in
audible distortion and possible speaker damage.
It will be necessary to re-adjust the
“Input Sens. for the affected channels if any
equalizer boost is activated after setting the
“Input Sens. with this procedure. This applies
to any EQ boost circuit, including source unit
tone controls or EQ circuits. EQ cuts will not
require re-adjustment.
JX250/1
Nom. Impedance Target AC Voltage
4 26.5 V
3 25.1 V
2 22.4 V
JX500/1D
Nom. Impedance Target AC Voltage
4 34.6 V
3 35.5 V
2 31.6 V
JX1000/1D
Nom. Impedance Target AC Voltage
4 44.7 V
3 47.4 V
2 44.7 V
Due to ongoing product development, all specifications are subject to
change without notice.
APPENDIX B:
Specifications
Input Section (all models):
Low-Level Input: Single-ended with RCA jacks
Low-Level Input Range: 200mV - 4V RMS
High-Level Input: Single-ended with molded connector
High-Level Input Range: 2.0V - 10.0V RMS
Signal Processing (all models):
Filter Type: 12dB/octave Low-Pass with continuously
variable cutoff frequency selection from 50 - 200 Hz.
Not defeatable.
Preamp Output: 2-Ch., pass-through with RCA-type jacks
Bass Boost: Single-band with 45 Hz center frequency,
adjustable from 0 to +12dB.
Remote Level Control: Via optional, wired RBC-1 remote
control knob. Full mute to 0 dB range. (RBC-1 is sold
separately.)
JX250/1 Specifications:
Amplifier Topology: Class A/B
Power Supply: Unregulated PWM switching type
Frequency Response: 10 - 150 Hz (+0/– 1 dB)
Signal to Noise Ratio:
>87 dBA referred to highest rated power, >63 dBA
referred to 1W (20 Hz - 20 kHz noise bandwidth)
Damping Factor: >160 @ 4 ohms
THD + Noise @ Rated Power: 1 %
Rated Continuous (RMS) Power @ 14.4V:
175W RMS x 1 @ 4
210W RMS x 1 @ 3
250W RMS x 1 @ 2
Rated Continuous (RMS) Power @ 12.5V:
130W RMS x 1 @ 4
170W RMS x 1 @ 3
210W RMS x 1 @ 2
Recommended Fuse Value (Type): 30A (MAXI or AGU)
Minimum Copper Power/Ground Wire Gauge: 8 AWG
Dimensions (LxWxH):
10.94" x 7.68" x 2.09" (278 mm x 195 mm x 53 mm)
Net Weight: 6.0 lbs. (2.72 kg)
7

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JL Audio 1D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JL Audio 1D in de taal/talen: Engels als bijlage per email.

De handleiding is 2,44 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info