167216
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
6
INSTALLATION AND SETUP
SETTING THE
CROSSOVER(S)
Determine your system plans and set the
crossover mode switch accordingly. If
you plan to use the GTO75.2 II or GTO75.4II
to drive full-range speakers, set the
crossover mode to FLAT and skip to
“Setting Input Sensitivity.
Initially set the crossover frequency
control midway. While listening to music,
adjust the crossover for the least
perceived distortion from the speakers,
allowing them to reproduce as much
bass as possible.
Systems using a separate subwoofer set
the crossover mode to HP (high pass) for
your full-range speakers. Adjust the
crossover frequency to limit bass and
provide increased system volume with
less distortion.
For subwoofers, choose the highest
frequency that removes vocal information
from the sound of the subwoofer.
If using the GTO75.2
II or GTO75.4 II to drive
a subwoofer(s), set the crossover mode to
LP (low pass).
NOTE: The GTO301.1II, GTO601.1II,
GTO1201.1II and the subwoofer output of
the GTO755.6 II are low-pass only and do
not have a crossover mode switch.
SETTING INPUT
SENSITIVITY
1. Initially turn the INPUT LEVEL control(s)
to minimum (counter clockwise).
2. Reconnect the (–) negative lead to the
vehicle’s battery. Apply power to the
audio system and play a dynamic music
track.
3. On the source unit, increase the volume
control to 3/4 volume. Slowly increase
the INPUT LEVEL control(s) toward three
o’clock until you hear slight distortion
in the music. Then reduce the INPUT
LEVEL slightly until distortion is no
longer heard.
NOTE: After the source unit is on, red LEDs
(on the top panel) will light, indicating the
amplifier is on. If not, check the wiring,
especially the remote connection from the
source unit. Also refer to “Troubleshooting”
on the next page.
REMOTE LEVEL CONTROL
The GTO755.6 II and all three GTO
subwoofer amplifiers have inputs for
an optional remote level control (RLC).
This will allow the amplifier’s input level
to be adjusted from the listening position.
Connect the optional remote level control
using the RJ-11 jack on the side of the
amplifier. Install the control module in the
front of the vehicle within easy reach of
the driver. Under the dash or in the center
console are both suitable locations.
SETTING THE BASS BOOST
The GTO755.6 II, GTO301.1II, GTO601.1II and
GTO1201.1II are all equipped with a bass-
boost control. This allows you to adjust the
bass output of your system at 50Hz up to
12dB and enhance low frequency.
AUX OUTPUT
GTO amplifiers (except GTO755.6 II) are
equipped with full-range outputs that can
be used to connect additional amplifiers.
NOTE: When using the high-level inputs,
the AUX outputs can be used to pass a
line-level signal to another amplifier.
INSTALLING NEON TUBES
(OPTIONAL)
1. Using a Phillips screwdriver, remove all
screws on the amplifier’s output/power
end panel and set them aside.
2. Using a 332-inch Allen wrench, remove
only the screws on the amplifier’s (top)
clear cover and set them aside.
3. Remove the end panel and slide the
cover off. Set both parts aside.
4. Locate the enclosed hardware bag and
remove the four clips. Each clip has a
square end and a larger round end.
Using a round end, press two clips onto
each neon tube (e.g., Street Glow AN9
or equivalent), as shown in
Figure 13.
5. For each tube, align both clips so the
square ends slide onto an exposed
extrusion edge, as shown in Figure 9.
Do not cover any screw holes. When
installed correctly, each neon tube will
sit under an extrusion and not be visible
when viewed from directly above.
6. Route each neon tube’s power cable
through its respective NEON hole on the
end panel (see
Figure 13).
7. Slide the cover back into place and re-
install its screws. Then, replace the end
panel and reinstall its screws.
8. Finish the installation of the neon tubes
as instructed in their owner’s manual.
Figure 12. Control end panel.
GTO75.2
II
GTO75.4 II
GTO301.1II, GTO601.1II, GTO1201.1II
GTO75.6 II
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JBL gto 601 1 ii bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JBL gto 601 1 ii in de taal/talen: Engels als bijlage per email.

De handleiding is 0,76 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info