648477
2
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
2
SUBWOOFER REAR-PANEL CONTROLS AND CONNECTIONS
1) Crossover Control: This control determines the highest frequency at
which the subwoofer reproduces sounds. The higher you set the Crossover
control, the higher in frequency the subwoofer will operate and the more its
bass will “overlap” that of the speakers. This adjustment helps achieve a
smooth transition of bass frequencies between the subwoofer and the
speakers for a variety of different rooms and subwoofer locations.
2) Phase Switch: This switch determines whether the subwoofer
transducer's piston-like action moves in and out in phase with the main
speakers. If the subwoofer were to play out of phase with the main
speakers, the sound waves from the main speakers could partially cancel
out the sound waves from the subwoofer, reducing bass performance and
sonic impact. This phenomenon depends in part on the placement of all the
speakers relative to the listening position and to each other in the room.
3) Bass Boost: When switched to 'On,' this boosts bass level for added
low-end power.
4) Power On Mode: When switched to 'Auto' position, the subwoofer will
then be in Standby mode. It will automatically turn 'On' when an audio signal
is detected at its inputs, and will return to the Standby mode when no audio
signal is detected by its inputs after approximately 10 minutes. Otherwise,
subwoofer will always remain powered until Power Switch is turned 'Off.'
5) Subwoofer Level: Use this control to adjust the subwoofer’s volume. Turn
the knob clockwise to increase the volume; turn the knob counterclock-wise
to decrease the volume.
6) On/Standby LED: When the Power switch is in the ‘On’ position, this
LED indicates whether the subwoofer is in the On or Standby state.
• When the LED glows green, the subwoofer is turned on.
• When the LED glows red, the subwoofer is in the Standby mode.
7) Line In/LFE Input Connectors:
When you’re connecting the subwoofer to the dedicated subwoofer
output of a receiver/processor that has its own low-pass crossover
network, use the LFE Input connector.
When you're connecting the subwoofer to the preamp or subwoofer
outputs of a receiver/processor that does not have its own low-pass
crossover network, use both Line In connectors and set the Input
Mode switch in the ‘Normal’ position. If your receiver/processor only
has one subwoofer output you can use either Line In connector.
8) Power Switch: Set this switch in the ‘On’ position to turn the
subwoofer on.
If you will be away from home, or will not be using the subwoofer for an
extended period, set this switch in the ‘Off’ position to conserve energy.
9) Power Cord: After you have made and verified the subwoofer’s input
connections, plug the power cord into an active, unswitched electrical outlet
for proper operation of the subwoofer.
DO NOT plug the power cord into the accessory outlets found on some
audio components.
POWER CORD
STUDIO
SUB 250P
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JBL Studio SUB 260P bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JBL Studio SUB 260P in de taal/talen: Engels als bijlage per email.

De handleiding is 2,14 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info