507346
3
Verklein
Vergroot
Pagina terug
1/4
Pagina verder
3
www.jbl.com
English
A. Loosen and remove the molded nut (2) by turning it
counterclockwise. Use the supplied metal bar (5) if necessary
by inserting it in one of the holes on the molded nut (2).
B. Pull the ball/shaft (3) out of the wall bracket (4).
C. Slide the molded nut (2) onto the ball/shaft (3) with threaded
opening facing the ball, and thread on the metal nut (1) all the way
onto the ball/shaft (3), with the nuts (1) “knurled surface facing
away from the ball.
D. Screw the ball/shaft (3) into the threaded 1/4"-20 insert (6) on
the back of the speaker cabinet until it is fully seated against the
bottom of the insert. Back out the ball-shaft assembly one half
turn and tighten the nut against the speaker. If the ball and shaft
assembly is not backed out before tightening the nut, performing
Step G below may dislodge the threaded insert in the speaker
housing and permanently damage the speaker.
E. Tighten theknurlednut (1) using a crescent wrench until it is firmly
seated against the back of the speaker and has fully locked the ball/
shaft (3) and the speaker cabinet together. Please note that once
this nut is tightened, it may embed some marks on the back of the
speaker where the attachment is made. However, these marks will
be covered by the nut (1).
F. The backup cord (8) is provided as an additional measure to prevent
the fall of the speaker in case the speaker becomes detached from
the wall bracket. One of the two lower screws (9) that attach the
wall bracket (4) to the wall will need to go through the eyelet (11)
at the end of the cord before going through the wall-bracket hole.
Make sure that the screw head is at least 0.36" (approximately 3/8")
or larger in diameter so that it can properly hold the backup cord
eyelet (11).
G. Mount the wall bracket (4) onto a wood stud on the wall, using #10,
minimum 1", panhead wood screws. Make sure that all four screws
are driven into the stud, not drywall.
If the bracket needs to be mounted on drywall, the use of properly
selected and installed wall anchors and screws is essential.
H. Holding the speaker cabinet (7) with both hands, reinsert the ball
portion of the ball/shaft (3) into the wall bracket (4).
I. Hand-tighten the molded nut (2) while positioning the speaker for the
intended orientation.
J. Once the orientation of the speaker is finalized, use the metal bar (5)
in one of the holes on the molded nut (2) and tighten securely.
K. Securely attach the other end (10) of the backup cord (8) to the
Control One AW by engaging it through the bar (12) on the back
speaker, as shown in the illustration.
Please note that while the JBL Control One AW is an all-weather
outdoor loudspeaker, it is not waterproof. The speakers should NOT
be submerged or directly exposed to water, ice, snow or sustained
moisture.
TO LEFT SPEAKER
+
TO LEFT SPEAKER
+
CORRECT INCORRECT
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JBL Control ONE AW bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JBL Control ONE AW in de taal/talen: Engels als bijlage per email.

De handleiding is 0,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van JBL Control ONE AW

JBL Control ONE AW Gebruiksaanwijzing - Nederlands - 7 pagina's

JBL Control ONE AW Gebruiksaanwijzing - Nederlands - 2 pagina's

JBL Control ONE AW Gebruiksaanwijzing - Deutsch - 7 pagina's

JBL Control ONE AW Gebruiksaanwijzing - English - 7 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info