756976
8
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
ENGLISH USER MANUAL
JB SYSTEMS 6/7 Club7usb
CONTROLS AND FUNCTIONS (rear)
32. MAINS CABLE: connect this cable to a 230V/50Hz mains outlet. Before use, inspect the cable to be
sure it’s not damaged!
33. POWER SWITCH: Used to turn the power of the mixer on and off. The blue led (7) is lit when the mixer
is turned on.
34. MASTER BALANCED OUTPUT: The XLR-connectors can be used to connect this mixer to any
balanced amplifier input, using special balanced signal cables.
35. [BOOTH] OUTPUT: The “[Booth]” output carries the same signal but can be controlled independently by
the “[BOOTH]” (10). Use the output to connect unbalanced amplifiers.
36. RECORD OUTPUT: Carries the same signal as the master outputs but is not influenced by the master
level and balance controls. Used to connect analog recording equipment. You can also connect a
computer for direct digital recording on the USB1 connection (46).
37. INPUT CHANNEL 4: used to connect line level audio signals. The input source selector (3) on the front
determines which input will be active.
38. INPUT CHANNEL 3 (CD): used to connect line level audio signals. The input source selector (3) on the
front has to be put to “[CD]”.
39. INPUT CHANNEL 3 (USB2/PH): used to connect phono level audio signals. The input source selector
(3) on the front has to be put to “[PHONO/USB2]”. Press switch (47) on the rear of the mixer to select the
phono input.
40. USB1/PH SWITCH: This switch makes it possible to switch between the phono input (41) and the USB1
input (46) on channel 3.
41. INPUT CHANNEL 2 (USB1/PH): used to connect phono level audio signals. The input source selector
(3) on the front has to be put to “[PHONO/USB1]”. Press switch (40) on the rear of the mixer to select the
phono input.
42. INPUT CHANNEL 2 (CD): used to connect line level audio signals. The input source selector (3) on the
front has to be put to “[CD]”.
43. LINE INPUT CHANNEL 1 (LN): used to connect a line level audio signal to channel 1. The input selector
(3) on the front has to be put to “[LINE]”.
44. LINE INPUT CHANNEL 1 (CD): used to connect a line level audio signal to channel 1. The input
selector (3) on the front has to be put to “[CD]”.
45. USB CONNECTION [USB2]: USB connection (USB2 for CH3). You can connect any PC through this
USB connection. The PC/Mac will detect your mixer as a sound card, normally no drivers are needed.
46. USB CONNECTION [USB1]: bidirectional USB connection (USB1 for CH2). You can connect any PC
through this USB connection. The PC/Mac will detect your mixer as a sound card, normally no drivers
are needed. Since the USB port is bidirectional you are able to play music on your computer and mix this
music with other sources like CD, phono, etc. At the same time you can record your mix on your
computer with the same USB connection
47. USB2/PH SWITCH: This switch makes it possible to switch between the phono input (39) and the USB2
input (45) on channel 2.
48. GROUND (GND) CONNECTION: Many Turntables have a GND-connection. It is preferable to connect
this signal ground to the GND-connector. If your turntable does not have a ground wire, you don’t have
to use this connector.
8

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw JB systems CLUB7-USB bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van JB systems CLUB7-USB in de taal/talen: Engels als bijlage per email.

De handleiding is 4,12 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van JB systems CLUB7-USB

JB systems CLUB7-USB Gebruiksaanwijzing - Nederlands - 10 pagina's

JB systems CLUB7-USB Gebruiksaanwijzing - Deutsch - 10 pagina's

JB systems CLUB7-USB Gebruiksaanwijzing - Français - 10 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info