578901
6
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
Measuring step length
To determine your step length, proceed as follows:
- Walking: walk 10 steps as you normally would, then measure the distance covered and divide it by ten.
Example:
You measure 6.2 metres. 6.2m / 10 (number of steps) = 0.62m (input step length WALK: 62cm).
- Jogging: here, we recommend that you jog at least 50 steps and then use the distance covered in the
calculation.
Step counter
As soon as you start to walk (see “Important” in Chapter 3!), the steps you take are added and displayed.
The distance, kcal and movement time are counted automatically (see Chapter 4.2/4.4 – 4.6)
Reset (RESET) the measured data
Press and hold the RESET key for at least 4 seconds. All data in the current measurement are then deleted
(Chapter 4.1/4.3 – 4.4: steps, distance, kcal, movement time). You can perform this RESET in all these
functions. However, the data for this deleted measurement are stored in the ODOSTEP and the STEP
TOTAL counter!
Caution: If you perform a RESET in the TOTAL STEP mode (Chapter 4.6), all measurement data, apart
from ODOSTEP, are reset to zero.
4.2 The function STEP (step counter)
As soon as you start to walk (see “Important” in Chapter 3!), the steps you take are added and displayed.
The distance, kcal and movement time are counted automatically (see Chapter 4.2/4.4 – 4.6)
Reset (RESET) the measurement data
Automatically: at midnight, the STEP counter (and the data in 4.4-4.6) is reset to zero.
Manually: press and hold the RESET key for at least 4 seconds. All data for the current measurement are
then deleted (Chapter 4.2 / 4.4– 4.6: steps, distance, kcal, movement time). You can perform this RESET in
all these functions. However, the data for this deleted measurement are stored in STEP TOTAL and
ODOSTEP!
Caution: If you perform a RESET in the TOTAL STEP mode (Chapter 4.6), the measurement data in the
daily memory (STEP) are also reset to zero. The data in ODOSTEP are retained.
4.3 The function ODOSTEP
You can use this function to monitor a training unit with all measurement data.
While you are in the ODOSTEP, you have to start the function by pressing and holding the SET button (hold
for about 4 secs until "ODO" in the top left corner is flashing).
By doing this, you start resp. continue a "training session". You may interrupt the recording by holding the
SET button for about 4 secs again (then ODO stops flashing).
Select the measurement data: with the SET key
You can delete the ODOSTEP separately. Other RESETs (in STEP TOTAL or STEP) do not have any effect
on ODOSTEP.
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Irox PE-DRO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Irox PE-DRO in de taal/talen: Engels als bijlage per email.

De handleiding is 0,27 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Irox PE-DRO

Irox PE-DRO Gebruiksaanwijzing - Deutsch - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info