578910
11
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
~P.11~
(E)
Very Weak Weak Medium Strong
[ ] button
Increases the value of a setting
Enable or disable the alarm when in Alarm display mode
[ ] button
Decreases the value of a setting
Activates manual synchanization for radio frequency
[ RESET ] button (inside battery compartment)
To activate system reset during abnormal condition.
B. DCF77 Radio Controlled Clock
The radio-controlled time is calculated by the Cesium Atomic clock of Braunschweig
(official clock of Germany). Then the time is coded and transmitted from Mainflingen
- near Frankfurt - via a signal on DCF-77 (77.5 kHz). The transmitting range of the
signal is 1500 km, which means that most of Western and Central Europe is covered
by this signal. Within this range the received time is completely accurate. Once sensor
signal(s) are received, the wave icon will flash to indicate that the receiving unit starts
to receive the DCF radio controlled time signal.
Radio Controlled wave icon can indicate 4 levels of signal status:
Once the time signal is received, the wave icon will stay on the LCD, and time and
calendar will automatically be updated.
Note: During 10 minutes of time signal reception, all manual settings will be sus-
pended. If setting is desired, press once [ ] key to deactivate the reception. You can
also press and hold the same key for 3 seconds to manually activate the reception in
normal mode.
C. Setting the clock, multi language, calendar, and temperature unit
1. Press & hold [MODE] button for 2 seconds. 12Hr/24Hr is blinking.
2. Use [ ] or [ ] button to select 12 or 24 hour format, then press [MODE] button to
confirm.
3. The hour digits will blink. Use [ ] or [ ] button to set the required time (each press
the button will increase or decrease the digits by one. Holding the button will cause
the setting to change rapidly). Press [MODE] button to confirm.
4. The minute digits will blink. Repeat the same procedures to enter minutes, Year
(range from 2005 to 2099),Date/Month or Month/Date format, current Month or Date
(Weekday auto selection), languages and °C or °F selection.
D. Setting the alarm
1. Press [ALARM] button once to switch from clock mode to display the alarm time, press
again to switch back to clock time display
2. Press [ALARM] button to display alarm time. Press & hold [ALARM] button 2 seconds
to enter alarm setting mode. The hour digit will blink.
3. Use [ ] or [ ] button to set the desired hour. Press [ALARM] button to confirm.
4. The minute digit will blink. Use [ ] or [ ] button to adjust minutes, and press [ALARM]
button to confirm.
5. The “%” bell icon will be shown to indicate the displayed alarm time is enable.
6. When the alarm is beeping, press [SNOOZE/LIGHT] button once to temporarily stop
the alarm for 10 minutes.
7. Press any button to stop the alarm (except [SNOOZE/LIGHT] button).
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Irox HELVET-X bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Irox HELVET-X in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 0,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info