585389
22
Verklein
Vergroot
Pagina terug
1/24
Pagina verder
70 71
6968
4c) MAXIMUM AND MINIMUM
TEMPERATURES AND HUMIDITY
The maximum and minimum recorded indoor temperature,
humidity and outdoor temperatures will be automatically
stored in memory. To display them, Press [ MEM ] once
to display the maximum readings and again the minimum
readings. The respective indicators,
[ MAX ] or [ MIN ] will be displayed.
To clear the memory, hold down [ MEM ] for two seconds.
The maximum and minimum readings will be erased.
If you press [ MEM ] now, the maximum and minimum
readings will have the same values as the current ones until
different readings are recorded.
4d) TEMPERATURE ALARM
Weather Station is equipped with a temperature alarm
whereby a user-defined temperature can be selected.
When the selected temperature is reached an acoustic alarm
will be initiated. Temperature alarm is programmed as
follows:
1. Press the [TEMP ALARM] button.
2. Hold the [TEMP ALARM] button for 2 seconds.
3. Select the desired temperature for the alarm by using the
[ ] or [ ] buttons.
With one further pressing of the TEMP ALARM button
the data entered is confirmed.
4. THERMOMETER / HUMIDITY
4a) HOW TO CHECK REMOTE AND
INDOOR TEMPERATURES
The wave display on the outdoors temperature indicates the
reception of the remote unit is in good order. If no readings
are received from the remote unit for more than two minutes,
blanks ” will be displayed until further readings are
successfully searched. Check the remote unit is sound and
secure. You can wait for a little while or Hold [ ] for 2
seconds to enforce an immediate search. If the temperature or
humidity goes above or below than the measuring range of
the main unit or the remote unit (stated in specification), the
display will show & “HHH” or “LLL” respectively.
The unit can be set to automatically scan and display
readings from the remote sensors, the display will show
the readings from one channel for about 4-seconds and
then proceed to the next channel display.
-To activate the remote-sensor scanning mode:
Press and the hold the button [CHANNEL] for 2 seconds.
-To deactivate the remote-sensor scanning mode:
Press and the hold the button [CHANNEL] for 2 seconds.
3b) BAROMETRIC PRESSURE TREND
The atmospheric pressure indicator, in the weather forecast
window, uses arrows to indicate if the atmospheric
pressure is increasing, remaining stable, or decreasing.
3. WEATHER FORECAST
3a) WEATHER FORECAST
The unit is capable of detecting atmospheric pressure
changes. Based on collected data, it can predict the weather
for the forthcoming 12 to 24 hours.
3b) Weather Forecast Alert
A weather forecast alert alarm will go on when the
weather forecast change to one of the status below:
Heavy rain, heavy snowy or unstable stormy weather.
The Weather Display backlight will be lighting up 2
minutes, the beep sound turns on and the storm symbol
will be shown on the display. To deactivate the
sound alert switch the [ALERT] button to “OFF”.
Arrow
indicator
Pressure
Trend
Steady FallingRising
NOTE:
1. It is not necessary and not possible to adjust the altitude
of the weather station. After the initial start-up of the
weather station, a first forecast will be made within the
first 24 hours of operation.
2. In periods of long stable weather conditions, it becomes
difficult to make a reliable forecast.
3. The weather forecast is solely calculated on the basis
of barometric air pressure changes.
4. The probability of a correct weather forecast is
approximately 70% and is valid for an area of approx.
20-30 km around the location of the weather station.
5. The forecast “Sunny” means at night “cloudless
weather”. Fogies not indicated by the weather station
as this can occur with different weather conditions.
6. If you travel with become impossible due to changes in
altitude and location. You'll have to wait up to 24 hour
so that the weather station can calculate a new forecast
based on the conditions at the new location.
Forecast
Symbols
Sunny Slightly Cloudy Cloudy
Snowy heavy snowyHeavy rainyLittle rainy
The unit is in searching mode.
Temperature readings are
securely registered.
No signals.
˚C
4b) HOW TO READ THE KINETIC WAVE DISPLAY
The kinetic wave display shows the signal receiving
status of the main unit. There are three possible forms:
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Irox HBR555t bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Irox HBR555t in de taal/talen: Duits, Engels, Frans, Italiaans als bijlage per email.

De handleiding is 4,64 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info