318183
11
Verklein
Vergroot
Pagina terug
1/14
Pagina verder
Reference Information
Troubleshooting Tips
My Roomba turns on, beeps and shuts off.
Roombas Main Cleaning Brush axles may be clogged with hair or other debris.
1. Make sure Roomba is fully charged and the Battery is properly seated.
2. If Roomba is charged,then empty the Particle Bin (see Emptying the Particle Bin on page 16) and follow the instruc-
tions for removing and cleaning the Main Brushes (see
Cleaning the Main Brushes on page 18).Pay special attention to
the Brush ends,or axles.
My Roomba is not working or there has been a decrease in the cleaning performance.
1. Ensure that the Battery is properly seated and charged.
2. Check that the Particle Bin (including the Filter Chamber) and Vacuum Inlet are empty, and that the Vacuum Impeller,
(the fan-shaped mechanism on the left side of the Vacuum Inlet) spins freely.(See the entire section entitled
Caring for
Your Roomba Pro,beginning on page 16 for more information.)
3. While you are examining the Filter Chamber, check the Air Filter (attached to the Filter Door) to make sure it is not
clogged or damaged.
4. Remove and examine all Brushes and their axles to make sure there is nothing wound around them (see
Cleaning the
Main Brushes on page 18 as well as Maintaining the Edge-Cleaning Side Brush on page 20).Also check to see there is
nothing wound around the Wheels or Wheel Axles.
My Roomba Gets Stuck.
Your Roomba may occasionally get stuck,especially in rooms that it has not cleaned before.If it does get stuck,Roomba
will try to free itself by turning in different directions.If it cannot free itself,Roomba will pause its cleaning cycle,flash its
Room Size Buttons and beep periodically for five minutes to let you know its stuck,before shutting off to conserve power.
Your Roomba might get stuck for several reasons:
1. It is wedged or pinned between or under narrowly spaced objects.
2. A cord,string,long rug fringe or carpet tassel is wound around its Brushes or Wheels.
3. One of the Wheels is no longer in contact with the ground.
4. Roomba bumps into objects and repositions them in such a way that an exit path no longer exists.
Move or block any object that Roomba gets stuck on or under.See the illustration entitled Roomba Care Hintson the
back cover of the Quick Start Guide to help identify and easily fix these problem areas.Once the problem areas have been
fixed,press the flashing Cleaning Cycle Button to continue Roombas cleaning cycle.If you wish to begin a new cleaning
cycle,press Roombas Power Button to turn it off,then turn it on again.Make sure the Particle Bin is empty and select the
desired Cleaning Cycle Button to start a new cleaning cycle
My Roomba Remote doesn’t work.
1. Make sure the Roomba Remote has new batteries.
2. Make sure that Roomba is operational by turning it on and off with the Main Power Button on Roomba. If Roomba
wont turn on, check that Roombas Battery is charged and completely installed.
2. Check that Roombas Beam Receiver (see Figure 3A) is clean by wiping it with a soft, dry cloth. Clean the Roomba
Remote’s transmitter area (on the front end of the Remote) by wiping it with a soft,dry cloth.
3. Make sure you are close enough to Roomba for the Remote to work.Try pointing the Roomba Remote at your Roomba
from less than 20 feet away, press the Power Button on the Roomba Remote and wait to hear Roombas Start-Up beep .
Ensure you are pointing the correct end at Roomba.
Maintaining the
Edge-Cleaning Side Brush
Periodically check the Edge-Cleaning Side Brush by
spinning it to ensure debris has not built up underneath it.
If it seems to be obstructed,remove and clean the Edge-
Cleaning Side Brush as follows:
1. If Roomba is on, turn it off and empty the Particle
Bin.Turn Roomba over so the cleaning surface is up.
Place it on a flat,padded surface.
2. Turn the Edge-Cleaning Side Brush so the Screw Head
can be accessed (see Figure 26).Point the screw head
towards Roombas Front Bumper,as shown below.
3. Using a small Phillips-head screwdriver, unscrew the
holding screw.
4. Pull the Edge-Cleaning Side Brush up and off of
Roomba.
5. Clean out any hair or other debris that may have
been caught under the Side Brush or on the Side
Brush Shaft.
6. Push the Side Brush back onto the Side Brush Shaft.
Screw the holding screw securely into the Edge-
Cleaning Side Brush,being careful not to over-tighten.
Keeping Roombas
Sensors Clean
Occasionally,lint or other debris will collect in Roombas
key sensor areas,which may cause Roomba to exhibit
unexpected movement behavior.If this happens,clean
these areas as follows:
1. If Roomba is on, turn it off and empty the Particle
Bin.Turn Roomba over so the cleaning surface is up.
Place it on a flat,padded surface.
2. Using a cotton swab,check and clean out any lint or
other debris from the four recessed sensor areas
located under the Front Bumper (Figure 27).
Side Brush
Figure 26: Unscrew
the holding screw
on the Spinning
Side Brush as
shown to remove
the brush.
Sensor Areas
Figure 27: Make sure that all four recessed
sensor areas under the front bumper are
kept free of dust and debris.
20
21
Pro Elite Manual MECH.qxd 7/11/03 11:35 AM Page 21
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Irobot roomba pro elite bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Irobot roomba pro elite in de taal/talen: Engels als bijlage per email.

De handleiding is 1,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info