686042
26
Verklein
Vergroot
Pagina terug
1/27
Pagina verder
265
A
S AVE THESE INSTRUCTIONS
(265IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2014
English
TROUBLESHOOTING (continued)
LED PANEL
CODE PROBLEM SOLUTION
LED Panel Code Flash & Alarm On (NOTE: Always turn off the power before cleaning and servicing).
E90
No water ow.
Turn off and unplug the control unit.
Ensure the outlet cover grid is clean and free from obstructions.
Clean or replace the cartridge, see Maintenance and Storage section.
Ensure the in/outlet connections on the spa tub and lter pump are not
blocked.
Keep the spa water properly sanitized to ensure a clean and unclogged
lter cartridge.
Press the button to turn off the unit. Release trapped air by
unscrewing the drain valve cap on the control base side with a coin.
Air has been release once a steady stream of water is owing out from
the drain valve. Wait for 15 seconds and screw the drain valve cap
back. Press the button to activate the control panel buttons, and
then run the lter function by pressing the button to push out any
remaining air in the system.
If problem persists, contact Intex Service Center.
E91
Dirt or scale on titanium plates.
Low salt level / No salt.
Electrolytic cell cord is loose.
Possible electrolytic cell failure.
Remove the electrolytic cell for inspection. Clean it if necessary. See
“Maintenance”.
Add salt. See “Salt Level Information”.
Ensure that the cell cord is plugged rmly into the cell receptacle.
Contact Intex Service Center. Replace the cell if needed.
E92 High salt level.
Partially drain the pool and re ll it with fresh water. See “Salt Level
Information”.
E94
Water temperature too low.
If the ambient temperature is below 4°C (39°F), we recommend not to
use the spa.
Turn off and unplug the control unit, add some warm water to raise the
spa water temperature above 5°C (41°F), then press the button to
heat up the water to the desired temperature.
If problem persists, contact Intex Service Center.
E95
Water temperature is
around 50°C (122°F).
Turn off and unplug the control unit. When the water has cooled down,
plug the RCD and restart all over again.
Turn the heater off, then press the lter and jet buttons to lower the
water temperature.
If problem persists, contact Intex Service Center.
E96
System Error.
Turn off and unplug the control unit, use the cap to stop the water
from owing out of the tub, disassemble and drain out the control unit.
Reassemble the control unit back to the tub. Plug the RCD and restart
all over again.
If problem persists, contact Intex Service Center.
E97 Dry- re Protection.
Contact Intex Service Center.
E99
Water temperature sensor broken.
Contact Intex Service Center.
END
After 72 hours of operation, the
pump will hibernate and the rapid
heating and water ltration
functions are disabled.
Press the button to re-active the lter pump.
Page 26
26

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex PureSpa - SJB-HS-20-1C bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex PureSpa - SJB-HS-20-1C in de taal/talen: Engels als bijlage per email.

De handleiding is 2,15 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Intex PureSpa - SJB-HS-20-1C

Intex PureSpa - SJB-HS-20-1C Gebruiksaanwijzing - Nederlands - 28 pagina's

Intex PureSpa - SJB-HS-20-1C Gebruiksaanwijzing - Deutsch - 29 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info