752322
9
Verklein
Vergroot
Pagina terug
1/13
Pagina verder
87A
SAVE THESE INSTRUCTIONS
English
(87IO) METAL FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 06/04/2019
Page 9
The last joint connection may be difficult to complete. You can
do it though, if you first simultaneously raise the last joint and
beam about 2 inches (5 cm). Now insert the beam into the joint
while lowering the pieces into position. The beam will easily
slide into the joint (see drawing 2.3). Ensure that the last joint
is fully connected before proceeding to connecting the legs.
3. Vertical legs assembly
Attach the leg’s end cap (4) to the bottom of each leg (7) first.
With the beams and T-joints assembly resting on the ground, slide
one vertical leg into the belt loop located in the middle of the pool
liner and insert the top of the leg into the bottom of the T-joint (3)
(see drawing 3.1). Continue the process with all the vertical legs.
Lift the beams assembly and make sure all the legs are in a vertical
position
(see drawing 3.2). Push all the T-joints downward to
ensure they are firmly connected to the legs.
Pull gently, in an outward direction, the bottom of the leg making
sure the leg is vertical and perpendicular to the level ground.
4. Filling of the pool
The following applies to pool liners with hose connectors (16’ (488 cm) & below pools). If the pool was
purchased without a filter pump, insert two of the three plugs (10) into the black filter pump outlets. Do
this from the inside of the pool so that water will not run out when filling it. If the pool was purchased
with a filter pump, read the Krystal Clear™ Filter Pump Manual first and then proceed to next installation
step.
Before filling the pool with water, ensure that the drain plug inside the pool is closed and that the drain
cap on the outside is screwed on tightly. Fill the pool with no more than 1 inch (2.5 cm) of water. Check
to see whether the water is level.
IMPORTANT: If the water in the pool flows to one side, the pool is not completely level. Setting
up the pool on unlevel ground will cause the pool to tilt resulting in the sidewall material bulging
and a potential collapse of the pool. If the pool is not completely level, you must drain the pool,
level the area or move the pool to a different area that is level, and re-fill the pool, following the
above directions.
Smooth out the bottom liner wrinkles (from inside the pool) by pushing out where the pool floor and pool
sides meet. Or, (from outside pool) reach under the side of the pool, grasp the pool floor and pull in an
outward direction. If the ground cloth is causing the wrinkles, have 2 people pull from opposite sides to
remove all wrinkles. Use the properly assembled pool ladder when entering or exiting the pool during this
process. Also make sure all the legs are vertical and perpendicular to the ground.
Fill the pool with water up to just below the sleeve line.
(see drawing 4).
POOL SETUP (continued)
4
WATER LEVEL
3.2
7
4
3.1
7
4
3
2.3
3
9

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intex 28200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intex 28200 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,71 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Intex 28200

Intex 28200 Gebruiksaanwijzing - Nederlands - 14 pagina's

Intex 28200 Gebruiksaanwijzing - Deutsch - 13 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info