625936
1
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
BATTERY
HOLDER
DOOR
PULL
TAB
FIG. 1
:
:
FIG. 2
FIG. 3 FIG. 4
TB121C DIGITAL TIMER INSTRUCTIONS
Manual Override:
To override the ON or OFF settings, press ON/OFF button. The override setting will
change at the next timed event.
Battery Replacement (See Fig 5 and 6):
When the batteries are running out, LO will be displayed.
1) Remove the timer from the wall socket.
2) Using a small flat screwdriver, pry the battery holder open. The TB121C uses 2
model L1154, SR44 or LR44 batteries.
3) Remove the old batteries (you have 1 minute to replace the batteries once the old
batteries are removed without losing the existing programs) and replace the new batter-
ies with the positive terminals facing as shown in fig. 6.
4) When the batteries are in place, press the battery holder back into its original position.
5) Plug the timer into the wall socket.
Reset (See Fig 7):
To quickly delete the time and event settings, at one time, using the point of a pencil,
press the RESET button found above the battery holder on the rear of the timer.
Ratings:
8.3 Amp Resistive, and Inductive
300 Watt Tungsten, 120VAC, 60Hz
WARNINGS:
1) DO NOT USE THE TIMER TO TURN OFF POWER FOR MAINTENANCE (repairs,
removing broken bulbs, etc.). ALWAYS TURN POWER OFF AT THE SERVICE PANEL
BY REMOVING A FUSE OR CIRCUIT BREAKER BEFORE DOING ANY CIRCUIT
REPAIRS.
LIMITED ONE YEAR WARRANTY
If within one (1) year from the date of purchase, this product fails due to a defect in material or workmanship, Intermatic
Incorporated will repair or replace it, at its sole option, free of charge. This warranty is extended to the original household pur-
chaser only and is not transferable. This warranty does not apply to: (a) damage to units caused by accident, dropping or abuse
in handling, acts of God or any negligent use; (b) units which have been subject to unauthorized repair, opened, taken apart or
otherwise modified; (c) units not used in accordance with instructions; (d) damages exceeding the cost of the product; (e) sealed
lamps and/or lamp bulbs, LEDs and batteries; (f) the finish on any portion of the product, such as surface and/or weathering,
as this is considered normal wear and tear; (g) transit damage, initial installation costs, removal costs, or reinstallation costs.
INTERMATIC INCORPORATED WILL NOT BE LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES. SOME STATES DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY
NOT APPLY TO YOU. THIS WARRANTY IS IN LIEU OF ALL OTHER EXPRESS OR IMPLIED WARRANTIES. ALL IMPLIED WARRANTIES,
INCLUDING THE WARRANTY OF MERCHANTABILITY AND THE WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, ARE HEREBY
MODIFIED TO EXIST ONLY AS CONTAINED IN THIS LIMITED WARRANTY, AND SHALL BE OF THE SAME DURATION AS THE WARRANTY
PERIOD STATED ABOVE. SOME STATES DO NOT ALLOW LIMITATIONS ON THE DURATION OF AN IMPLIED WARRANTY, SO THE ABOVE
LIMITATION MAY NOT APPLY TO YOU.
This warranty service is available by either (a) returning the product to the dealer from whom the unit was purchased,
or (b) mailing the product, along with proof of purchase, postage prepaid to the authorized service center listed
below. This warranty is made by: Intermatic Incorporated/After Sales Service/7777 Winn Rd., Spring Grove, Illinois
60081-9698/815-675-7000 http://www.intermatic.com Please be sure to wrap the product securely to avoid
shipping damage.
INTERMATIC INCORPORATED
SPRING GROVE, ILLINOIS 60081-9698 158TB11844
FIG. 5
FIG. 6
RESET BUTTON
FIG. 7
TB121C DIGITAL TIMER INSTRUCTIONS
Thank you for purchasing the TB121C Digital Timer.
Features:
•Easysetup
•2on/2offsettings
•5Ft.cord
•Canbeusedforincandescentlightsupto300Watts
•ManualOverride
Set Up:
Batteries Activation-The timer is shipped with 2 batteries (L1154/SR44/LR44) installed.
Pull the protective strip from the battery carrier (See Fig 1). The display will flash 12:00AM.
(Note: To conserve battery power, if the timer is not plugged in and no button is pushed,
the display will go blank. To restore, press any button).
Clock (See Fig 2):
1)Press SET button once. The display will advance to TIME mode and the time will be
flashing.
2)Press + or – button until time of day is displayed. Holding either button down will
increase the speed of the setting.
On/Off Time:
1)After the time is set, press SET button once. The display will now show EVENT 1 ON
mode. EVENT 1 ON will be flashing with a blank display. (See Fig. 3)
2)Press + or – to advance to the ON time.
3)Once the ON time is set, press SET button once. The display will now show EVENT 1
OFF. (See Fig 4)
4)Press + or – to advance to the OFF time.
5)Repeat Steps 1-4 for the 2nd ON/OFF settings.
6)When timer events are completed, press SET once. This will put the timer in RUN
mode. The display will show the time of day entered, with the colon flashing.
Note: To clear an event time, push + and – buttons at the same time while in the ON or
OFF mode that you want to clear
Lamp Connection:
1)Turn lamp switch to ON position.
2)Plug lamp into the receptacle located on the cord.
3)Plug the Timer Cord into the wall outlet.
1

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Intermatic TB121C DIGITAL TIMER bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Intermatic TB121C DIGITAL TIMER in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 0,17 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info