118456
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
INTRODUCTION
The Infresco has been designed specifically to work with Infra Red Heaters, with a rating of 4kW it
will allow you to control a variety of heating and lighting solution.
The Infresco has a 1 to 10 step setting allowing you to find the optimum comfort setting in you
specific area. With energy saving a major factor in the design brief, once the Infresco is switched
on it will automatically manage the heating system. With a built in temperature sensor only
allowing the unit to switch on when required and a PIR that will detects a requirement for the
heater to switch on only when needed. An optional remote control allows for the unit to be fitted
out of the way so safety is paramount. The Infresco has a built in soft start function which will add
up to an additional 30% life to your heater lamp.
APPLICATIONS
Any application were high inrush current is an issue or control is required. Typical use is for Infra Red
Heating lamps, Garden lighting
FEATURES
Soft Start – up to 30% extended life of Lamp
Variable Control – Ability to find comfort level
Simple Installation – Ability to plug directly in 13A Plug with up to 3kW load
Energy Saving – Automated system. (Only heat when required)
Temperature Monitoring – If ambient temperature is above preset the Infresco unit remains
switched off
SAFETY FIRST
Please read these instructions before installing and operating this product. (See warning for
additional information).
Installation
The ideal site for the PIR to be mounted is approximately 2.5 + Meters of the floor. Ceiling
mounting is preferred but not essential
The PIR must not be mounted.
Directly in line of the lamps output
Highly reflective surfaces
Radiators or other thermostatically controlled heaters
Open door ways with people walking past
Commissioning
NOTE: On switch on the PIR takes 60 seconds to set before detection takes place
NOTE: The PIR continues to monitor the area and will reset to the set time every time it detects
movement.
Before testing ensure the wiring is correct. The temperature trip point has already been preset at
the factory. The timer is preset to 5 minutes.
The expected detection area can now be “walked tested” using the diagram shown in mind. The
area should be crossed in various directions to ensure coverage is as expected.
Display Features
Display shows ‘t’ The Infresco is turned OFF as the ambient temperature
is above the trip level set by TEMP. SET.
Display shows ‘F’ The Infresco is set to FULL output.
Display decimal point pulses The PIR input is waiting to be enabled i.e. no movement.
Display decimal point fully on The Infresco is in Standby mode pressing the remote
control POWER button will toggle the power ON and OFF.
You can check the remote control is transmitting by observing the decimal point flashing rapidly.
UijthovenInfrarood
Nijverheidstraat31
4261TKWijkenAalburgTheNetherlands
Phone:0031416532724
Fax:0031416532719
Email:info@uithoven.nl
Web:www.terrastopper.nl
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Infresco Dimmer 6Kw bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Infresco Dimmer 6Kw in de taal/talen: Engels als bijlage per email.

De handleiding is 1 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info