Handleiding Indesit KP 648 MS (pagina 30 van 33) (Duits, Deens)

512953

Verklein

Vergroot

Pagina terug

1/33

Pagina verder

fig.9

fig.10

INSTALLATION

fig.8

Gas supply

• Check that the appliance is set for the type of gas available

and then connect it to the mains gas piping or the gas

cylinder in compliance with the applicable norms in force.

• This appliance is designed and set to work with the gas

indicated on the label situated on the actual hob. If the gas

supply is different from the type for which the appliance

has been set, replace the corresponding nozzles (provided),

following the instructions given in the paragraph "Adaptation

to different types of gas".

• For trouble-free operation, suitable use of energy and a

longer life cycle for the appliance, make sure that the supply

pressure complies with the values indicated in table 1

"Burner and nozzle specifications", otherwise install a

special pressure regulator on the supply pipe in compliance

with current standards and regulations.

• Connect in such a way that the appliance is subjected to

no strain whatsoever.

Either a rigid metal pipe with fittings (fig. 8-D) in compliance

with norms must be used for connecting to the nipple union

(threaded - cylindrical ½"G fitting "F") situated at the rear of

the appliance (fig. 8), or a flexible steel pipe with a continuous

wall and fittings (fig. 8-C) in compliance with norms, which

must not exceed 2000 mm in length. Check that the connecting

pipe cannot come into contact with moving parts which could

damage or crush it. For installation with a flexible rubber

pipe, apply the special hose support for liquid gas (fig. 8-A)

or natural gas (fig. 8-B). The gasket "G" (provided) must be

utilised in every type of connection. The two ends of the pipe

must be fastened with the purpose designed pipe collars "E",

in compliance with the norms. The flexible pipe should comply

with the norms, and be specific for the type of gas used. In

addition:

• it should be as short as possible, with a maximum length

of 1.5 metres;

• it should not be bent or kinked;

• it should not be in contact with the rear panel of the appli-

ance or in any case with parts which may reach a tem-

perature of 50°;

• it should not pass through holes or slits used for discharg-

ing the oven flue gases;

• it should not come into contact with pointed parts or sharp

corners;

• it should be easy to inspect along its entire length in order

to be able to check its condition;

• it should be replaced before the date printed on the actual

pipe.

Important: A pressure regulator, in compliance with the

applicable norm in force, must be inserted when

connecting to a liquid gas supply (in a cylinder).

Upon completion of installation, check for leaks from the

gas circuit using a soapy solution (never use a flame). Make

sure that the natural gas pipe is adequate for a sufficient

supply to the appliance when all the burners are lit.

Adapting to different types of gas

To adapt the hob to a different type of gas from the factory-

set one (indicated on the rating plate at the top of the hood

or on the packaging), the burner nozzles should be replaced

as follows:

• Remove the hob grids and slide the burners off their seats.

• Unscrew the nozzles (fig. 9), using a 7 mm socket span-

ner and replace them with nozzles for the new type of gas

(see table 1 "Burner and nozzle characteristics").

Reassemble the parts following the above procedure in

the reverse order.

• On completing the operation, replace the old rating label

with the one showing the new type of gas; the sticker is

available from our Service Centres.

Adjusting the primary air of the burners

The primary air of the burners does not need to be adjusted.

Adjusting the low flame

• Turn the tap to the low flame position;

• Remove the knob and turn the adjusting screw, situated to the

right of the tap (fig. 10) until you obtain a regular small flame,

using a screwdriver (loosening the screw increases the height

of the flame, tightening decreases it).

N.B.: In the case of liquid gas, the regulation screw must

be screwed in all the way.

• Having obtained the low flame setting required and with the

burner lit, abruptly change the position of the knob several times

from minimum to maximum and vice versa and check that the

flame does not go out.

• In appliances fitted with the safety device (thermocouple), should

the device fail to work with the burners set to the low flame

setting, increase the low flame setting of the same on the ad-

justing screw.

Once the adjustment has been made, remount the seals on the

by-passes using sealing wax or similar.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

lees eerst de handleiding door;
controleer of uw vraag al eerder door iemand anders is gesteld;
probeer uw vraag zo duidelijk mogelijk te stellen;
heeft u een probleem en al geprobeerd om dit op te lossen, vermeld dit erbij aub;
heeft u een oplossing gekregen van een bezoeker dan horen wij dat graag in dit forum;
wilt u een reactie geven op een vraag of antwoord, gebruik dan niet dit formulier maar klik op de knop 'reageer op deze vraag';
uw vraag wordt direct op de website gezet; vermijd daarom persoonlijke gegevens in te vullen;

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Indesit KP 648 MS Handleiding

Hulp nodig? Stel uw vraag in het forum

Misbruik melden

Product:

Spelregels forum

Abonneren

Ontvang uw handleiding per email

Uw handleiding is per email verstuurd. Controleer uw email

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

U heeft geen emailadres opgegeven

Uw vraag is op deze pagina toegevoegd

Info