24011
12
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
12
EN
Whenever the appliance fails to work, check for a solution from the following list before calling for Technical
Assistance Centre.
Troubleshooting
Malfunction:
The dishwasher does not start.
No water enters the dishwasher.
No water drains out from the
dishwasher.
The dishwasher makes excessive
noise.
The dishes and glasses are
covered in a white film or
limescale deposits.
The dishes and glasses are
streaked or have a bluish tinge.
The crockery has not been dried
properly.
The dishes are not clean.
Tap shut-off alarm.
(several short beeps are emitted)
(the 20 min. and 10 min. indicator
lights flash)
Clogged filter alarm
(the "Wash cycle in progress" and 10
min. indicator lights flash)
Water loading solenoid valve
malfunction alarm
(the 20 min. indicator light flashes)
Possible causes / Solutions:
The plug has not been inserted into the electrical socket
properly, or there is no power in the house.
The dishwasher door has not been shut properly.
A delayed start has been programmed (
see Start-up and use
).
There is no water in the mains supply.
The water inlet hose is bent (
see Installation
).
The dishwasher cycle has not yet finished.
The water outlet hose is bent (
see Installation
).
The drain duct is blocked.
The filter is clogged up with food residues.
The dishes are rattling against each other or against the sprayer
arms.
The level of the refined salt is low or the dosage setting is not
suited to the hardness of the water (
see Rinse aid and salt
).
The lid on the salt dispenser is not closed properly.
The rinse aid has been used up or the dosage is too low.
The crockery is made from non-stick material.
The rinse aid dosage is too high.
The rinse aid has been used up or the dosage is too low (
see
Rinse aid and salt
).
The rinse aid dispenser setting is not high enough.
A wash cycle without a drying programme has been selected.
The racks are overloaded (
see Loading the racks
).
The crockery has not been arranged well.
The sprayer arms cannot move freely.
The wash cycle is too gentle (
see Wash cycles
).
The detergent has not been measured out correctly or it is not
suited to the type of wash cycle (
see Start-up and use
).
The filter is dirty or blocked (
see Care and maintenance
).
The refined salt level is low (
see Rinse aid and salt
).
Turn on the tap and the appliance will start after a few minutes.
The appliance lock has been activated because no action was
taken when the beeps sounded. Switch off the machine using the
ON/OFF button, turn on the tap and switch the machine back on
after 20 seconds by pressing the same button. Re-programme
the machine and restart the wash cycle.
Switch off the machine by pressing the ON/OFF button and clean
the filters (see Maintenance), then switch the dishwasher back on
by pressing the same button. Re-programme the machine and
restart the wash cycle.
Switch off the appliance by pressing the ON/OFF button and
switch it back on after a minute. If the alarm continues, shut off
the water tap to eliminate the risk of flooding, remove the plug
from the electrical socket and contact Assistance.
195051409.01
09/2005-Xerox Business Services
12

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Indesit IDTM bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Indesit IDTM in de taal/talen: Engels als bijlage per email.

De handleiding is 0,39 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Indesit IDTM

Indesit IDTM Gebruiksaanwijzing - Nederlands, Deutsch, English - 80 pagina's

Indesit IDTM Gebruiksaanwijzing - English - 24 pagina's

Indesit IDTM Gebruiksaanwijzing - Français - 80 pagina's

Indesit IDTM Gebruiksaanwijzing - Français - 24 pagina's

Indesit IDTM Gebruiksaanwijzing - Italiano, Português, Espanôl - 80 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info