•Command table (continued)
0E B0 Set as non-select channel
B1 Set as select channel
D0 Set scan resume OFF
D3 Set scan resume ON
0F 00 Turn the split function OFF
01 Turn the split function ON
10 Select simplex operation
11 Select –DUP operation
12 Select +DUP operation
10 00 AM/FM/WFM modes:
Select 10 Hz tuning step
SSB/CW/RTTY modes: TS OFF
01 Select 100 Hz tuning step
02 Select 1 kHz tuning step
03 Select 5 kHz tuning step
04 Select 9 kHz tuning step
05 Select 10 kHz tuning step
06 Select 12.5 kHz tuning step
07 Select 20 kHz tuning step
08 Select 25 kHz tuning step
09 Select 100 kHz tuning step
10 AM/FM/WFM modes:
Select MHz step
SSB/CW/RTTY modes: Invalid
11 — Select/read attenuator (0=OFF,
12=ON (12 dB))
13 00 Announce with voice synthesizer
01 (00=all data; 01=frequency and
02 S-meter level; 02=receive mode)
14 01 + Level data [AF] level setting (0=max. CCW to
255=max. CW)
02 + Level data [RF] level setting (0=max. CCW to
255=11 o’clock)
03 + Level data [SQL] level setting (0=11 o’clock to
255=max. CW)
06 + Level data NR level setting (0=min. to
255=max.)
07 + Level data Inside [PBT] setting or IF shift
setting (0=max. CCW, 128=cen-
ter, 255=max. CW)
08 + Level data Outside [PBT] setting
(0=max. CCW, 128=center,
255=max. CW)
09 + Level data CW Pitch setting (0=300 Hz,
128=600 Hz, 255=900 Hz, in 5 Hz
steps)
0A + Level data RF Power setting (0=mini. to
255=max.)
0B + Level data MIC Gain setting (0=mini. to
255=max.)
0C + Level data Key Speed setting (0=slow to
255=fast)
0D + Level data NOTCH (NF1) frequency setting
(0=low freq. to 255=high freq.)
0E + Level data COMP Level setting (0=0 to
10=10)
0F + Level data Break-IN DELAY setting (20=2.0d
to 130=13.0d)
12 + Level data NB level setting (0=0 to
255=100%)
15 + Level data Monitor gain setting (0=0 to
255=100%)
16 + Level data VOX gain setting (0=0 to
255=100%)
14 17 + Level data Anti-VOX gain setting (0=0 to
255=100%)
18 + Level data Contrast (LCD) setting (0=0 to
255=100%)
19 + Level data Bright (LCD) setting (0=0 to
255=100%)
1A + Level data NOTCH (NF2) frequency setting
(0=low freq. to 255=high freq.)
15 01 Read squelch condition
02 Read S-meter level
11 Read RF power meter
12 Read SWR meter
13 Read ALC meter
14 Read COMP meter
16 02 Preamp (0=OFF; 1=ON)
12 AGC selection
(1=Fast; 2=Mid; 3=Slow)
22 Noise blanker (0=OFF; 1=ON)
40 Noise reduction (0=OFF; 1=ON)
41 Auto notch (0=OFF; 1=ON)
42 Repeater tone (0=OFF; 1=ON)
43 Tone squelch (0=OFF; 1=ON)
44
Speech compressor (0=OFF; 1=ON)
45 Monitor (0=OFF; 1=ON)
46 VOX function (0=OFF; 1=ON)
47 Break-in (0=OFF; 1=semi break-
in; 2=full break-in)
48
Manual notch (NF1) (0=OFF; 1=ON)
4B DTCS (0=OFF; 1=ON)
4C VSC (0=OFF; 1=ON)
4F Twin Peak Filter (0=OFF; 1=ON)
50 Dial lock function (0=OFF, 1=ON)
51
Manual notch (NF2) (0=OFF, 1=ON)
19 00 Read the transceiver ID
1A 00 Send/read memory contents (see
p. 146 for details)
01 Send/read band stacking register
contents (see p. 146 for details)
02 Send/read memory keyer contents
(see p. 146 for details)
03 Send/read the selected filter width
(SSB, CW, RTTY:
0=50 Hz to 40/31=3600/2700 Hz;
AM: 0=200 Hz to 49=10 kHz)
04 Send/read the selected AGC time
constant (0=OFF, 1=0.1/0.3 sec. to
13=6.0/8.0 sec.)
050001 RF Power setting (0=mini. to
255=max.)
050002 MIC Gain setting (0=mini. to
255=max.)
050003 Send/read of SSB TX bandwidth
(lower edge) for wide
(0=100, 1=200, 2=300, 3=500 HZ)
050004 Send/read of SSB TX bandwidth
(higher edge) for wide (0=2500,
1=2700, 2=2800, 3=2900 HZ)
050005 Send/read of SSB TX bandwidth
(lower edge) for middle
(0=100, 1=200, 2=300, 3=500 HZ)
050006 Send/read of SSB TX bandwidth
(higher edge) for middle (0=2500,
1=2700, 2=2800, 3=2900 HZ)
Command Sub command Description Command Sub command Description
143
17
CONTROL COMMAND
