521907
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
8 9
3. Installation and Operation
3.1 Powering up the Flood Sensor
Remove the battery cover; insert new batteries, noting the
polarity as shown in Fig. 1, and replace the cover. (Requires
2x AAA batteries).
Low battery indication: If the batteries need to be replaced,
the RED LED on the transmitter will ash slowly.
3.2 Installing the Flood Sensor
Mount the transmitter on a xed surface such as a wall using
either double-sided adhesive strips or the screws and wall
plugs provided.
When mounting the water sensor part of the Flood Sensor use
the double-sided adhesive pad. If mounting onto on a porous
surface such as wood or concrete, make sure the surface is
painted to provide proper adhesive bonding.
After installing, test the Flood Sensor using a bowl of water to
be certain it is working properly.
3.3 Installing using Double-Sided Adhesive Pads
• Ensure the mounting surface is clean.
Peel back one layer of the protective lm and attach it to the
transmitter.
Peel back the remaining layer of protective lm and press the
transmitter rmly in place against the mounting surface until
attached.
• Repeat the process to attach the water sensor.
4. House Security Code Settings
Unless the factory settings of the i.onik
®
Alarmsystem Smart
Panel have been altered, the house security code will NOT need
to be changed.
However, if the settings on the Smart Panel have been altered,
or need to be altered to solve the problem of the Smart Panel
and sensors activating intermittently (or not working at all) or
interference with other systems, then the house security code
on all system modules (sensors and sirens)will also need to be
changed.
House Security Code settings can be altered as follows:
• There are 4 jumpers or dip-switches on each device.
Remove the jumper compartment cover, then pull out or plug
the jumper into the contacts to change the House Security
Code.
If a jumper is plugged it is ON if it is removed it is OFF. Default
code is with all the jumpers plugged.
To ensure the system works correctly, make sure the jumpers
on the Smart Panel and all other system modules (sensors and
sirens) match exactly.
Jumpers for
house
security code
- Smart Panel
- Each sensor
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
*Jumper:
ON = Plugged,
OFF = Pull Out
Dip-Switches
for house
security code
- Key Fob Remote
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
5. Zone Code Settings
The sensor is supplied with a pre-assigned zone setting.
The sensor can be assigned to a different zone as follows:
Unscrew and remove the jumper compartment cover on the
rear of the sensor.
In the area marked “Zone Code” there are eight pairs of
metal contacts with a number next to each.
The number corresponding to the pair of contacts which is
plugged with a jumper is the current zone.
To re-assign to a different zone simply unplug the jumper
from its current zone and plug it across the contacts corres-
ponding to the new zone number selected.
Jumpers for
zone code
Default zone code: Zone 1
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw I-onik WS-106 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van I-onik WS-106 in de taal/talen: Duits, Engels als bijlage per email.

De handleiding is 0,33 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info