521909
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
hometec
hometec
WS-103
Quick Start Guide
Motion Sensor
English
Please keep these instructions in a safe place for future
reference.
Kit Contents:
1x i.onik
®
Motion Sensor
1x Ball-head joint mounting bracket
3x Screws and wall plugs
1x Instruction leaet
1. Introduction
The i.onik
®
Motion Sensor is designed to trigger the i.onik
®
Alarm-
system Smart Panel when it senses movement in a given area.
Note:
Where pets are in the home it is advised that they are not
allowed onto higher surfaces (above 1 m in height) where they
may trigger the sensor.
2. Location
First determine the location of the Sensor, which should be placed:
On a solid surface between 1.8 m to 2.4 mm (6 ft to 8 ft) from the
oor.
• Near key entry/exit points.
Away from extreme temperature sources (radiators, ovens, stoves
etc.) and large metal objects that could interfere with the wireless
performance.
• Away from direct sunlight.
• Indoors only and not behind partitions.
Where better transmitter/reception performance can be achieved
(if necessary).
3. Installation and Operation
3.1 Powering up the Motion Sensor
Remove the battery cover, insert and connect a
9 V battery as shown in diagram below and
replace the cover (Requires 1x 9 V battery).
Low battery indication: If the batteries need to
be replaced, the RED LED will ash (not inclu-
ding entry/exit delay ashing).
3.2 Installing the Motion Sensor
Hold the enclosed mounting template against the wall at the selected
location and mark the points for drilling.
• Drill the holes and insert wall plugs.
Attach the bracket to the mounting surface with the screws provided.
• Attach the Motion Sensor to the mounting bracket.
3.3 Sensor Sensitivity
IMPORTANT! The Motion Sensor is designed with a power saving
program and will remain inactive for 3 minutes after each detection.
Please bear this in mind during system set up.
The sensitivity of the Motion Sensor is adjustable and can be chan-
ged by setting the connector on either the “High”, “Middle” or “Low”
position. When the sensitivity is set to “Low”, more movement is
required to trigger the sensor. It is recommended to set the sensitivity
to “Low” and perform a “Walk Test” (described in section 3.4). If the
walk test result is satisfactory, the sensitivity does not require further
adjustment. If the walk test result shows the sensitivity is too low,
then the sensitivity can be set to “Middle” or “High” as required. It
is recommended that a walk test be conducted after each change in
sensitivity setting.
3.4 Walk test
After mounting the sensor at the desired location,
it is important to perform a walk test in order to
determine if the sensor is detecting the correct
area. The distance at which the sensor can detect
motion can be adjusted by altering the angle of the
sensor. To reduce the detection range, simply move
the sensor downward and move the sensor upward to maximize
the range.
Note:
Enter into ALERT mode before you perform the walk test, so
that the alarm is not triggered.
You should walk in the area that you would like the sensor
to monitor. If movement is detected the red light inside the
unit will appear. If the red light does not appear, adjust the
mounting angle accordingly. Perform the walk test again after
3 minutes. Repeat this procedure until motion is detected.
Whilst carrying out the test, there should be no movement in
the detection area during the 3 minute interval.
Tips:
The sensor should not face towards direct sunlight, be placed near
heat or cold producing devices (i.e. air conditioning, radiators, fans,
ovens, heaters etc.) that may cause false triggers. Also perform the
walk test in areas which the sensor is not intended to cover, to ensure
movement cannot be detected.
4. House Security Code Settings
Unless the factory settings of the i.onik
®
Alarmsystem Smart Panel
have been altered, the House Security Code will NOT need to be chan-
ged. However, if the settings on the Smart Panel have been altered,
or need to be altered to solve the problem of the Smart Panel and
sensors activating intermittently (or not working at all) or interference
with other systems, then the House Security Code on all system mo-
dules (sensors and sirens) will also need to be changed.
House Security Code settings can be altered as follows:
• There are 4 jumpers or dip-switches on each device.
Remove the jumper compartment cover, then pull out or plug the
jumper into the contacts to change the House Security Code
If a jumper is plugged it is ON if it is removed it is OFF. Default code
is with all the jumpers plugged.
To ensure the system works correctly, make sure the jumpers on
the Smart Panel and all other system modules (sensors and sirens)
match exactly.
5. Zone Code Settings
The sensor is supplied with a pre-assigned Zone setting. The sensor
can be assigned to a different zone as follows:
Unscrew and remove the battery compartment cover on the rear of
the sensor.
In the area marked “Zone Code” there are eight pairs of metal con-
tacts with a number next to each.
The number corresponding to the pair of contacts which is plugged
with a jumper is the current zone.
To re-assign to a different zone, simply unplug the jumper from its
current zone and plug it across the contacts corresponding to the
new zone number selected.
6. Maintenance
The product may be cleaned with a soft damp cloth and then wiped
dry. Do not use abrasive, solvent based or aerosol cleaners as this
may damage and/or discolour the product.
Do not allow water to enter or attempt to clean inside the unit.
7. Batteries
Do not allow the batteries to corrode or leak as this may cause per-
manent damage to the product. Take care to insert the batteries with
the correct polarity as shown inside the battery compartments. Do not
mix new and old batteries or different types of batteries. Do not use
rechargeable batteries.
At the end of their useful life the batteries should be disposed of
via a suitable recycling centre. Do not dispose of with your normal
household waste. DO NOT BURN.
8. Alarm System Limitations
Even the most advanced alarm systems cannot guarantee 100 % pro-
tection against burglary or environmental problems. All alarm systems
are subject to possible compromise or failure-to-warn for a variety of
reasons.
Please note that you may encounter problems with your system
if:
The Smart Panel is not placed within hearing range of persons slee-
ping or remote parts of the premises.
• The sensors are placed behind doors or other obstacles.
Intruders gain access through unprotected points of entry (where
sensors are not located).
Intruders have the technical means of bypassing, jamming,
or disconnecting all or part of the system.
• The power to the sensors is inadequate or disconnected.
The sensors are not located in proper environmental/temperature
conditions i.e. too close to a heat source.
Note:
Inadequate maintenance is the most common cause of alarm
failure; therefore, test your system at least once per week to
be sure the sensors and sirens are working properly.
Although having an alarm system may make you eligible for
reduced insurance premiums, the system is no sub-stitute for
insurance.
Chips and More GmbH
Gewerbestr. 7 | 79112 Freiburg | Germany | www.i-onik.de
Service: + 49 7664 403 69 12
Email: support@i-onik.de
Weitere Informationen und Erklärungen zur Handhabung des Alarmsystems finden Sie unter www.i-onik.de
For more details and questions on how to operate the alarm kits, please go to www.i-onik.de
Move the sensor
downward to reduce
the range.
Move the sensor
upward to maximize
the range.
Jumpers for house security code - Smart Panel
- Each sensor
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
*Jumper:
ON = Plugged,
OFF = Pull Out
Dip-Switches for house security code
- Key Fob Remote
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
Jumpers for zone code Default zone code: Zone 1
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw I-onik WS-103 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van I-onik WS-103 in de taal/talen: Duits als bijlage per email.

De handleiding is 0,29 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info