521910
2
Verklein
Vergroot
Pagina terug
1/2
Pagina verder
English
Please keep these instructions in a safe place for future reference.
Kit Contents:
1x i.onik
®
Door/Window Sensor
1x Magnetic contact
1x Double-sided adhesive pad
1x Instruction leaet
1. Introduction
The i.onik
®
Door/Window Sensor consists of two parts, a transmitter
and a magnetic contact. Once this sensor is installed, with the trans-
mitter fastened to the frame and the magnet to the door or window,
the sensor will trigger and transmit a message to the i.onik
®
Alarm-
system Smart Panel when the door or window is opened.
2. Location
First determine the location of the Sensor, which should be placed:
• In the most vulnerable rooms or near key entry/exit points.
Away from extreme temperature sources (radiators, ovens, stoves
etc.) and large metal objects that could interfere with the wireless
performance.
• Away from direct sunlight.
• Indoors only and not behind partitions.
Where better transmitter/reception performance can be
achieved (if necessary).
3. Installation and Operation
3.1 Powering up the Door/Window Sensor
Remove the battery cover; insert new
batteries noting the polarity as shown in
Fig. 1 and replace cover. (Requires
2x AAA batteries)
Low battery indication: If the batteries need
to be replaced, the RED LED on the transmitter
will ash slowly.
3.2. Installing the Door/Window Sensor
Mount the transmitter on a xed surface such as a door or a window
frame.
Mount the magnet on a movable surface such as a door or a window.
Ensure the >/< marks on the sides of the transmitter and magnet
match up as shown in Fig. 2.
The transmitter and the magnet
must be no more than 5 mm
apart.
3.3. Mounting with the Double-
Sided Adhesive Pad
Ensure the mounting surface is
clean.
Peel back one layer of the protective
lm and attach it to the transmitter.
Peel back the remaining layer of protective lm and press the trans-
mitter rmly in place against the mounting surface until rmly
attached.
• Repeat to attach the magnet.
4. House Security Code Settings
Unless the factory settings of the i.onik
®
Alarmsystem Smart Panel
have been altered, the House Security Code will NOT need to be
changed.
However, if the settings on the Smart Panel have been altered, or
need to be altered to solve the problem of the Smart Panel and sen-
sors activating intermittently (or not working at all) or interference
with other systems, then the House Security Code on all system
modules (sensors and sirens)will also need to be changed.
House Security Code settings can be altered as follows:
• There are 4 jumpers or dip-switches on each device.
Remove the jumper compartment cover, then pull out or plug the
jumper into the contacts to change the House Security Code.
If a jumper is plugged it is ON if it is removed it is OFF.
Default code is with all the jumpers plugged.
To ensure the system works correctly, make sure the jumpers on
the Smart Panel and all other system modules (sensors and sirens)
match exactly.
Jumpers for house security code - Smart Panel
- Each sensor
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
*Jumper:
ON = Plugged,
OFF = Pull Out
Dip-Switches for house security code
- Key Fob Remote
Default house code:
1: ON, 2: ON, 3: ON, 4: ON
5. Zone Code Settings
The sensor is supplied with a pre-assigned Zone setting. The sensor
can be assigned to a different zone as follows:
Unscrew and remove the jumper compartment cover on the rear of
the sensor.
In the area marked “Zone Code” there are eight pairs of
metal contacts with a number next to each.
The number corresponding to the pair of contacts which is plugged
with a jumper is the current zone.
To re-assign to a different zone simply unplug the jumper from its
current zone and plug it across the contacts corresponding to the
new zone number selected.
Jumpers for zone code Default zone code: Zone 1
6. Maintenance
The product may be cleaned with a soft damp cloth and then wiped
dry. Do not use abrasive, solvent based or aerosol cleaners as this
may damage and/or discolour the product.
Do not allow water to enter or attempt to clean inside the unit.
7. Batteries
Do not allow the batteries to corrode or leak as this may cause per-
manent damage to the product. Take care to insert the batteries with
the correct polarity as shown inside the battery compartments. Do not
mix new and old batteries or different types of batteries. Do not use
rechargeable batteries.
At the end of their useful life the batteries should be disposed of
via a suitable recycling centre. Do not dispose of with your normal
household waste. DO NOT BURN.
8. Alarm System Limitations
Even the most advanced alarm systems cannot guarantee 100 % pro-
tection against burglary or environmental problems. All alarm systems
are subject to possible compromise or
failure-to-warn for a variety of reasons.
Please note that you may encounter problems with your system
if:
The Smart Panel is not placed within hearing range of persons slee-
ping or remote parts of the premises.
• The sensors are placed behind doors or other obstacles.
Intruders gain access through unprotected points of entry (where
sensors are not located).
Intruders have the technical means of bypassing, jamming,
or disconnecting all or part of the system.
• The power to the sensors is inadequate or disconnected.
The sensors are not located in proper environmental/temperature
conditions i.e. too close to a heat source.
Note:
Inadequate maintenance is the most common cause of alarm
failure; therefore, test your system at least once per week to
be sure the sensors and sirens are working properly.
Although having an alarm system may make you eligible for
reduced insurance premiums, the system is no sub-stitute for
insurance.
Fig. 1
Transmitter
Magnet
Battery Compartment
Cover
2x AAA Batteries
(not incl.)
Fig. 2
Chips and More GmbH
Gewerbestr. 7 | 79112 Freiburg | Germany | www.i-onik.de
Service: + 49 7664 403 69 12
Email: support@i-onik.de
Weitere Informationen und Erklärungen zur Handhabung des Alarmsystems finden Sie unter www.i-onik.de
For more details and questions on how to operate the alarm kits, please go to www.i-onik.de
hometec
hometec
WS-102
Quick Start Guide
Door/Window Sensor
2

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw I-onik WS-102 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van I-onik WS-102 in de taal/talen: Duits als bijlage per email.

De handleiding is 0,34 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info