627060
21
Verklein
Vergroot
Pagina terug
1/48
Pagina verder
21
CHANGES AND TYPING ERRORS RESERVED CHANGES AND TYPING ERRORS RESERVED
5. General descripTion
Figure 1 – Construction of the machine
1 Headstock 18 Foot brake
2 Speed switch High/Low 19 Spindle control lever
3 Electric control box 20 Hand wheel of longitudinal feed (traverse adjustment)
4 Chuck 21 Lever of hand wheel of longitudinal feed
5 Tool post 22 Chip tray
6 Work lamp 23 Apron
7 Compound rest 24 Feed shaft selector
8 Hand wheel of compound rest 25 Thread cutting lever
9 Coolant 26 Rack
10 Cross slide 27 Control rod
11 Tailstock spindle clamping lever 28 Lead screw
12 Tailstock spindle hand wheel 29 Gear box
13 Tailstock 30 Feed switch
14 Tailstock clamping lever 31 Feed switch
15 Tailstock set screw 32 Gear box cover
16 Feed switch (longitudinal/cross) 33 Feed switch (direction)
17 Bed 34 Speed selection lever
5.1 bed
The bed is made of a high-grade low vibration cast iron (FCD25). By combining high sidewalls with strong cross ribs,
a bed of low vibration and rigidity is produced. The two precision ground V-sideways are an accurate guide for the
support and tailstock. The main motor is mounted on the rear of the bed.
5.2 headsTock
The headstock is cast from a high-grade low vibration cast iron. It is bolted to the bed, using four screws and four
adjusting screws for alignment with the head. The large main spindle is mounted on two precision taper roller
bearings (#7212). The hole of the spindle measures 35 mm. A quick change of the belt can be accomplished by
easing the tension on the idler. The belt type used in this lathe has the advantage that it makes no noise at any
speed.
5.3 sUpporT
The bed slide is made from high quality cast iron; the sliding parts are smooth ground. It slides over the bed without
play and can be easily adjusted. The cross slide is mounted on the bed slide and moves on a dove tailed slide. Play in
the cross slide may be adjusted by means of the wedges. Use the hand wheel to move the cross slide. A graduated
collar is placed on the hand wheel; one graduated mark equals 0.0254 mm. The tool slide is mounted on the cross
slide and can be rotated 360º. The tool and cross slide travel on dovetailed slides and have wedges, adjustable nuts
and graduated collars. The four-way tool holder is mounted on the tool slide. For accurate results, tightening the hex
nut can lock the support.
5.4 apron
The apron is mounted on the bed slide and moves on a dovetailed slide. A half nut is fitted into the apron. The half
nut gibes can be adjusted from the outside. The half nuts are responsible for the connection with the thread cutting
axis. A gear shaft, moved by a hand wheel on the support, and a rack, which is mounted on the bed, achieve quick
travel of the bed travel.
5.5 TailsTock
The tailstock slides on a V-way and can be clamped at any location by means of a bolt. A MT2 spindle with graduated
scale is part of the tailstock. The clamping handle makes clamping of the spindle possible. By turning the hand
wheel, the spindle can be moved.
5.6 oTher parTs
The lead screw is located on the front of the bed and is connected to the gear box on the left side. The gear box is
made from high quality cast iron and is mounted on the left side of the bed. It is a 9-speed motor. Always change the
speed to bring the idler in the right position. The motor is mounted on the rear of the bed.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Huvema-HU-1010-B-4-SINO

Zoeken resetten

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Huvema HU 1010 B-4 SINO bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Huvema HU 1010 B-4 SINO in de taal/talen: Engels als bijlage per email.

De handleiding is 7,37 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Huvema HU 1010 B-4 SINO

Huvema HU 1010 B-4 SINO Gebruiksaanwijzing - Nederlands - 48 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info