518168
40
Verklein
Vergroot
Pagina terug
1/44
Pagina verder
38
Care of your Scandinavia 200
Trouble Shooting
Checking the Needle
Always start with a new needle as soon as
you discover that a stitch is not what you
expected. Test sew on a scrap of the fabric
you are sewing. Check that you have chosen
the correct needle and see that it is correctly
inserted.
Unattractive Stitches
The thread tension is not correct. Make
sure that the thread is not catching. Certain
thread spools are unsuitable for spooling
from the horizontal spool pin. Try instead
with the vertical spool pin. The machine
may be incorrectly threaded. Be sure to
place spool holders correctly.
Wrong bobbin thread. It should be of the
same thickness as the upper thread.
The Needle Breaks
The needle can strike against stitch plate and
break. Change the needle. Do not pull fabric
as you sew, let the machine feed.
The Upper Thread Breaks
Check the thread spool to see that it has
not caught in any way. The needle eye may
have sharp edges which cut the thread. If so,
change the needle.
The upper thread is incorrectly threaded.
The upper thread may have too much
tension.
The hole in the stitch plate may be chipped
and have sharp edges. We recommend that
you replace it.
The Bobbin Thread Breaks
The bobbin thread may be incorrectly
threaded. The stitch plate hole is damaged.
See "Upper thread breaks".
Irregular Thread Tension
This may be due to poor quality thread.
When sewing with cotton thread, increase
the thread tension.
The Machine Does Not Feed the Fabric
The stitch length is too short. Increase stitch
length.
The feed teeth may be lowered. Raise them
by turning the dial to
.
The feed teeth are full of dust and dirt.
Clean with the brush.
The Seam is Too Loose – Fabric Layers
Not Held Together
The thread tension is far too loose. Adjust
the thread tension.
Incorrect Stitch
If the machine does not sew the stitch
indicated by the display, it is possible that
the electronics have been disturbed in
some way, perhaps by a short power cut or
electrical disturbance.
Shut off the main switch, wait a few seconds
and try again. If the fault remains, contact
your dealer.
Machine Runs Sluggishly
Dirt or lint has built up under the stitch
plate. Remove the plate and brush clean
between the feed teeth and in the bottom
area.
Main motor does not work
The electronic overload protector may have
switched off. Shut off the main switch, wait
about a minute. Then turn on the machine.
Expert assistance
Have your machine "tuned up" regularly
by your dealer. If you have followed
the preceding points and still do not
get satisfactory results, you should
contact the dealer where you bought
the machine. When the machine is
being checked, it is a great help if it can
be test sewn under conditions that are
similar to when you used it.
Remember to take a sewing sample
along with you, preferably the fabric
and the thread you intend to use.
A sewing sample will often give much
better information than words.
Non-original Parts and Accessories
The warranty does not cover any defect
or damage caused by use of non-
original accessories or parts.
40

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna SCANDINAVIA 200 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna SCANDINAVIA 200 in de taal/talen: Engels als bijlage per email.

De handleiding is 3,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Husqvarna SCANDINAVIA 200

Husqvarna SCANDINAVIA 200 Gebruiksaanwijzing - Nederlands - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info