477578
22
Verklein
Vergroot
Pagina terug
1/112
Pagina verder
22
From the rear of the tractor, slide the lower clevis assembly
(12) onto the right side bagger support tube (10). Line up the
center hole (13) on upper bracket with the hole in the bagger
support tube (10) and secure lower clevis assembly (12) with
clevis pins (14) and clips (15).
Install the actuator (16) as shown. Use the spacers (17) to
center the actuator (16) between both the upper and lower
brackets and secure with clevis pins (18) and clips (19).
TO INSTALL BAGGER SPRING LATCH
The bagger spring latches are located on the back plate (1),
one in each of the bottom corners.
Before installing, tractor engine must be shut off and parking
brake engaged.
Install each bagger spring latch with the loop end (2) down
and facing towards the bagger assembly.
Place the mounting bolt (3) through the backplate. Place
curved end of the bagger spring latch onto mounting bolt (3)
and secure with nut (4) as shown. Tighten firmly.
BAGGER SPRING LATCH ADJUSTMENT
If the bagger assembly height is adjusted, it may be necessary
to adjust the bagger spring latch. To adjust, remove the nut (4)
and move the bagger spring latch to the appropriate hole in the
backplate (1), ensuring the bagger assembly will be securely
closed. Retighten nut securely.
NOTE: The bottom of the bagger assembly should contact the
loop end so that it is held securely when closed.
TO INSTALL BAGGER FULL LEVER/EXTENSION
Before installation or adjusting, tractor engine must be shut off
and parking brake engaged.
Remove center discharge chute. (See "To Remove Center
Chute" in section 6 of this manual.)
Remove bolt (1). Place lever (2) into slot and reinstall bolt
(1). Adjust as needed.
TO ADJUST BAGGER FULL LEVER/EXTENSION
Slide bagger full extension (3) to the desired position.
For the heaviest/wet grasses, slide extension all the way in.
For the lightest/driest grasses, pull extension all the way out.
Route cable assembly (20) between the lower clevis assem-
bly (12) and along bagger support tube (10), and connect the
cable assembly (20).
Using the switch (21) on the right side fender, fully extend
the actuator (16). Secure any excess cable assembly to
the bagger support tube (10) with the zip ties (22). Retract
the actuator (16) and check to ensure there are no snags or
binds in the cable assembly (20).
Install the bagger assembly.
NOTE: Both cross tubes (23) on the bagger support weldment
need to be placed onto the top support assemblies (24). Extend-
ing the actuator slightly will help make installation easier. Once
installed, adjust bagger assembly as needed. (See "To Adjust
Bagger" in this section of the manual.)
23
24
21
16
16
22
10
20
12
10
20
2
1
3
4
14
15
10
13
12
18
17
16
18
19
19
2
1
2
3
22

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna CTH184T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna CTH184T in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 7,45 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info