477580
21
Verklein
Vergroot
Pagina terug
1/96
Pagina verder
21
2
TO ASSEMBLE BAGGER
Unfold bag and stand right side up.
Feed front bagger frame (1) up through fabric loops at each
side of bagger.
Snap bottom of front bagger frame (1) into snap feature at
front of bagger bottom.
Slide bagger fabric loop (2) segments at the ends of bag
onto top bagger frame tubing.
Uninstall two (¼”-20 x 1.15”) hex bolts (3) from the front of
top frame.
Reinstall the two (¼”-20 x 1.15”) hex bolts (3) through holes
at top of the front bagger frame and thread into nuts inside
the tubing of top bagger frame.
Uninstall (1/4”-20) lock nuts (4) at bottom of front bagger frame.
Unfold cross braces (5) and attach to carriage bolts at bottom
corners of front bagger frame.
Reinstall (1/4”-20) lock nuts (4) and tighten until fully seated.
Install corner support brackets.
Place the bottom of the corner support bracket (6) into
the corner of the bagger bottom.
Push corner support bracket into the corner until the upper
hole is aligned with the hole in the upper bar.
Secure corner support bracket to the upper bar (7) with
fastener (8).
Push the bottom of the corner support bracket (6) forward
as shown to secure it in the proper position.
Repeat procedure on other side.
Remove clevis pin (9) and retainer spring (10) from bagger
handle (11).
Slide bagger handle (11) down through bagger cover and
frame upper weldment holes.
Reinstall clevis pin (9) through hole at bottom of bagger
handle and slide retainer spring (10) into hole at the end of
the clevis pin until it locks into place
3
2
1
5
6
7
8
4
11
10
9
HORIZONTAL ADJUSTMENT
Loosen nuts on carriage bolts (3) to allow the adjustment plate
(4) to slide forward or rearwards. Move as needed. Retighten
nuts securely, locking the adjustment plate in its new position.
Repeat on opposite side.
1
2
A
3
4
TO ADJUST HANGER BRACKETS
The tractor comes from the factory with the bagger pivot bracket
preset in a fixed position. If necessary, this position can be adjusted
to maintain a consistent gap (A) between the fender and the bag-
ger assembly top. An ideal gap is approximately 0.2” (5.1mm).
NOTE: As desired, the hanger bracket on either side can be
adjusted in this manner.
Remove bagger assembly.
NOTE: ADJUST ONLY ONE SIDE AT A TIME.
VERTICAL ADJUSTMENT
Loosen nuts on carriage bolts (1) to allow the adjustment plate
(2) to slide up or down. Move as needed. Retighten nuts
securely, locking the adjustment plate in its new position.
Repeat on opposite side.
Readjust if necessary.
21

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna CTH163T bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna CTH163T in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans als bijlage per email.

De handleiding is 7,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info