40844
26
Verklein
Vergroot
Pagina terug
1/40
Pagina verder
26 – English
WORKING TECHNIQUES
Felling
Felling is done using three cuts. First you make the directional
cuts, which consist of the top cut and the bottom cut, then you
finish with the felling cut. By placing these cuts correctly you
can control the felling direction very accurately.
Directional cuts
To make the directional cuts you begin with the top cut. Stand
to the right of the tree and cut on the pull stroke.
Next make the bottom cut so that it finishes exactly at the end
of the top cut.
The directional cuts should run 1/4 of the diameter through
the trunk and the angle between the top cut and bottom cut
should be 45°.
The line where the two cuts meet is called the directional cut
line. This line should be perfectly horizontal and at right
angles (90°) to the chosen felling direction.
Felling cut
The felling cut is made from the opposite side of the tree and
it must be perfectly horizontal. Stand on the left side of the
tree and cut on the pull stroke.
Make the felling cut about 3-5 cm (1.5-2 inches) above the
bottom directional cut.
Set the spike bumper (if one is fitted) just behind the felling
hinge. Use full throttle and advance the chain/bar slowly into
the tree. Make sure the tree does not start to move in the
opposite direction to your intended felling direction. Drive a
wedge or breaking bar into the cut as soon as it is deep
enough.
Finish the felling cut parallel with the directional cut line so
that the distance between them is at least 1/10 of the trunk
diameter. The uncut section of the trunk is called the felling
hinge.
The felling hinge controls the direction that the tree falls in.
All control over the felling direction is lost if the felling hinge is
too narrow or non-existent, or if the directional cuts and felling
cut are badly placed.
When the felling cut and directional cut are complete the tree
should start to fall by itself or with the aid of a felling wedge or
breaking bar.
!
WARNING! Unless you have special training
we advise you not to fell trees with a
diameter larger than the bar length of your
saw!
26

Hulp nodig? Stel uw vraag in het forum

Spelregels
1

Forum

Husqvarna-455-Rancher

Zoeken resetten

  • beste .. ik werk met een husvarna455Ranger maar mijn toprol komt regelmatig vast te zitten ; het is prutsen om dat weer los te krijgen .. ik zaag stammen van den maar ze zijn nogaal droog .. mijn vraag waar kan ik de ketting oil toevoer op Max zetten .. alvast bedankt als je antwoord Gesteld op 23-7-2024 om 11:35

    Reageer op deze vraag Misbruik melden
  • Heeft iemand de gebruiks aanwijzing voor een husqvarna 51 kettingzaag Gesteld op 29-10-2011 om 18:56

    Reageer op deze vraag Misbruik melden
    • Hallo,
      Heb je al een gebruiksaanwijzing van Husqvarna 51/55
      Mocht je interesse hebben, dan wil ik hem wel copieren, tegen verzend kosten.
      gr ruud Geantwoord op 17-2-2012 om 11:08

      Waardeer dit antwoord (1) Misbruik melden

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Husqvarna 455 Rancher bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Husqvarna 455 Rancher in de taal/talen: Engels als bijlage per email.

De handleiding is 2,5 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Husqvarna 455 Rancher

Husqvarna 455 Rancher Gebruiksaanwijzing - Nederlands - 40 pagina's

Husqvarna 455 Rancher Gebruiksaanwijzing - Deutsch - 84 pagina's

Husqvarna 455 Rancher Gebruiksaanwijzing - English - 44 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info