661708
5
Verklein
Vergroot
Pagina terug
1/60
Pagina verder
5
GB
Contents
A
Auto Reel
B
Wall Bracket
C
Feeder Hose
D
Threaded Tap Connector
E
Hose End Connector
F
Waterstop Connector
G
Wall Plugs and Screws
H
Hose Nozzle
Quick hints and tips
When mounting the reel, ensure that nothing
obstructs the reel from swinging freely through 180°.
It is critical to use a 7mm drill when drilling holes to
mount the reel.
Ensure the wall bracket is mounted vertically using a
spirit level.
Check that the reel is locked onto the bracket before
turning on water supply.
The hose will not rewind unless it is pulled a short
distance (15 to 30cm) away from the reel and then
walked back towards the reel.
If the hose will not rewind, try the following;
Turn off the tap and let the water out of the hose by
opening the hose nozzle/gun.
Walk back to the reel with the end of the hose and
trigger the rewind mechanism by taking hold of the
hose near to the reel, and gently pull the hose about
15 to 30cm to release the latch.
(Ensure that nothing is obstructing the hose whilst
the rewind procedure is active.)
Use the lock on the side of the reel to lock the hose
when not in use.
Assembly and installation
of the Auto Reel
TOOLS NEEDED:
Flat-ended, long shaft screwdriver
Philips, long shaft screwdriver
• Pencil
• Tape measure
7mm diameter masonry drill bit
Electric drill/hammer drill
• Spirit level
SELECT A SUITABLE POSITION
FOR INSTALLATION
Fig 1.
The reel is designed for external use and is not
suitable for use with indoor taps, unless used with
an appropriate Indoor Tap Connector
(Part No’s; 2159, 2176, 2177, 2274, which are not
supplied)
The reel should be able to swing through 18.
Allow 65cm of clearance on both sides of the wall
bracket. (See Fig.1)
If the hose is to be used around corners, the wall
bracket should be mounted at least 1.60m from the
corner, and a hose guide should be used
(part no; 2392, which is not supplied.)
MOUNT THE WALL BRACKET
Fig 2.
Remove the Wall bracket (Contents B) from the reel
by releasing the locking clasp on the reel (Fig.2a).
The wall bracket can now be removed ready for
mounting.
Important: Ensure that the wall bracket is vertical
(with the padlock loop (see fig 6. a) pointing down)
using a spirit level, and that the correct size holes
(7mm diameter and 50mm deep) are drilled
(Fig.2b).
Use the four wall plugs and screws supplied
(Contents G). The plugs and screws supplied are
designed for use on standard brick and concrete
walls. To fix the bracket to any other surface, you
should use screws and plugs appropriate for that
surface.
CONNECT THE FEEDER HOSE
AND FITTINGS
If the feeder hose supplied is too short to reach your
tap, replace it with a good quality 12.5mm (½) hose.
Fig 3 – Attaching the Feeder Hose:
Lay the reel on a soft surface with side
A
uppermost
and remove the side disc using a flat headed
screwdriver (Fig.3a).
Unscrew the hose nut from the inlet adapter (Fig.3b).
Push the feeder hose underneath the hose bridge,
put the nut over the hose (Fig.3c).
Push the end of the hose into the inlet teeth and
tighten the nut (Fig.3d). Ensure that the hose is
pushed all the way into the inlet. Re-fit the side disc
(Fig.3e).
Attach the hose end connector (Contents E) to the
free end of the feeder hose. Attach the water stop
connector (Contents F - Pre fitted for the Flowmax
model) to the watering hose and connect the nozzle/
gun supplied to the water stop connector (Contents
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hozelock 2597 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hozelock 2597 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2,68 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info