6 04.2007 TR10A041-C RE
TABLE OF CONTENTS PAGE
A Supplied items 2
B Required tools for installation 2
1 IMPORTANT NOTES 7
1.1 Important safety instructions 7
1.1.1 Warranty 7
1.1.2 Checking the door / door system 7
1.2 Important instructions for a safe installation 7
1.2.1 Before installing the garage door operator 7
1.2.2 Carrying out the installation work 8
1.3 Warnings 8
1.4 Maintenance advice 8
1.5 Information on the illustrated section 8
Illustrated section 24-49
2 INSTALLATION INSTRUCTIONS 61
2.1 Garage door operator 61
2.2 Required clearance for installing the operator 61
2.3 Latching on a sectional door 61
2.4 Centrally positioned lock on a sectional door 61
2.5 Off-centred reinforcement profile on a sectional door 61
2.6 Latching on an up-and-over door 61
2.7 Up-and-over doors with an ornamental wrought
iron handle 61
2.8 Boom 61
2.9 Before installing the boom 61
2.10 Installing the boom 61
2.11 Boom operating modes 61
2.11.1 Manual operation 61
2.11.2 Automatic operation 61
2.12 Establishing the end-of-travel positions by
installing the limit stops 61
2.13 Tensioning the toothed belt 62
3 INSTALLING THE GARAGE DOOR OPERATOR
AND ACCESSORIES 62
3.1 Notes on electrical work 62
3.2 Electrical connection / terminals 62
3.3 Operator lighting 62
3.4 Connecting additional components / accessories 62
3.5 Connecting an external radio receiver 62
3.6 Connecting external impulse buttons to start or
stop door cycles 62
3.7 Connecting the IT3b internal push-button unit 62
3.7.1 Impulse button to start or stop door cycles 62
3.7.2 Light switch to switch the operator lighting on/off 62
3.7.3 Push-button to switch all the control elements on/off 62
3.8 Connecting a two-wire photocell 62
3.9 Connecting a self-monitoring wicket door contact 62
3.10 Connecting a closing edge safety device 62
3.11 Connecting the HOR1 option relay 62
3.12 Connecting the UAP1 universal adapter print 62
4 PUTTING THE OPERATOR INTO SERVICE 63
4.1 General information 63
4.2 Menu selection 63
4.3 Putting into service 63
4.4 MENU J – adjustment / setting of the door type 63
4.5 MENU 1 – learning cycle / programming the
operator 63
4.5.1 Programming the travel limits and the attached
safety devices 63
4.6 Resetting the control system / restoring the
factory settings 63
5 HAND TRANSMITTER 64
5.1 Important notes on the use of the hand transmitter 64
5.2 Restoring the factory code 64
6 FUNCTION SELECTION 64
6.1 MENU P 64
6.1.1 Programming a radio code using the internal
radio receiver 64
6.1.2 Deleting all the radio codes of a function 65
6.1.3 Setting the "partial opening" position 65
6.1.4 Setting the reversing limit "closing edge safety
device / leading photocell" 65
6.2 MENU 2 65
6.2.1 Setting the operator lighting – persistence time 65
6.2.2 Setting the operator lighting – radio signal,
external push-button 65
6.2.3 External radio function of the 2nd channel 65
6.3 MENU 0 – normal operation 66
6.3.1 Behaviour of the garage door operator after
2-3 fast-opening cycles in succession 66
7 SPECIAL MENUS 66
7.1 Selecting the special menus 66
7.2 General information on the special menus
(menu 3 – menu A)66
7.2.1 7-segment display when changing from the
customer menu to the special menus 66
7.2.2 7-segment display after selecting a special menu 66
7.3 MENU 3 – automatic timed closing 66
7.4 MENU 4 – safety devices 67
7.5 MENU 5 – setting of:
- advance warning phase
- options relay
- maintenance indication 67
7.5.1 Maintenance indication 67
7.5.2 Overview of maintenance intervals 67
7.6 MENU 6 – force limit during operation in the
CLOSE direction 67
7.6.1 Checking the forces in the CLOSE direction 67
7.7 MENU 7 – behaviour during operation in the
CLOSE direction 68
7.8 MENU 8 – force limit during operation in the
OPEN direction 68
7.8.1 Checking the forces in the OPEN direction 68
7.9 MENU 9 – behaviour during operation in the
OPEN direction 68
7.10 MENU A – maximum force 69
8 ERROR MESSAGES AND WARNINGS 69
9 DISMANTLING 69
10 TERMS OF WARRANTY 69
11 TECHNICAL DATA 69
11.1 Spare lamp 70
ENGLISH
