594363
4
Verklein
Vergroot
Pagina terug
1/61
Pagina verder
GETTING TO KNOW YOUR CLEANER
ASSEMBLING YOUR CLEANER
Remove all components from the packaging.
1. Connect the hose to the cleaner main body, ensuring it clips and locks into position. To
release: simply press the two buttons on the hose end and pull [2].
2. Connect the tube upper end to the handle. [3].
3. Connect the tube lower end to the carpet and oor nozzle [4].
USING YOUR CLEANER
CLEANER MAINTENANCE
Replacing The Dust Bag
If the bag check indicator is red please check and, if necessary, replace the bag.
1. Lift the bag door release latch [13] to open the cover, pull the bag holder [14] and pull the
bag collar to remove the bag [15].
2. Apply the peel and seal sticker, located on the bag collar, to the bag inlet. The full dust bag
should be disposed of correctly and carefully.
3. Fold a new bag as shown on the bag and t by inserting the collar into the bag holder.
4. Ret the bag holder and close the bag door.
Warning - The bag door will NOT close if the dust bag and/or the bag holder are not assembled
to the cleaner. Always ensure the bag and bag holder are present when closing the bag door.
Remember: The bag check indicator may also be red if an obstruction has occurred. In this
case refer to ‘Removing A Blockage From the System.
Cleaning the Filters
To maintain optimum performance of your cleaner, please wash the lters after each 5 bag changes.
Cleaning the pre-motor lter:
1. Lift the bag door release latch [13] to open the cover and remove the bag holder.
2. To remove the pre-motor lter slide the pre-motor lter frame from the cleaner. [16]
3. Remove the lter from the holder. [17]
4. Wash it in hand warm water, [20] and allow it to dry thoroughly before replacing to the
cleaner [21].
Cleaning the exhaust lter:
1.
To remove the exhaust lter, unclip the exhaust lter cover [18] and remove the lter pack. [19]
2. Wash the lter in hand warm water [20] and allow it to dry thoroughly before replacing to
the cleaner. [21].
Remember: Do not use hot water or detergents. In the unlikely event of the lters becoming
damaged, t a Genuine Hoover replacement. Do not try and use the product without a dust
bag or lter tted.
Cleaning the permanent cloth dust bag*
To maintain optimum performance we recommend that you wash the permanent cloth dust
bag under hand warm water after every 5 full bags. Remove excess water and leave to dry fully
before replacing.
2
GB
1. Extract power cord and plug it into the power supply. Do not pull the cord beyond the red
marker [5].
2. Adjust the length of the telescopic tube* by moving the telescopic release button* up and
raise or lower the handle to the most comfortable cleaning position [6].
3. Carpet & Floor Nozzle. Press the pedal on the nozzle [7] to select the ideal cleaning mode
for the oor type.
Hard Floor: The brushes are lowered to protect the oor
Carpet: With lifted brushes for the deepest clean
4. Switch the cleaner on by pressing the On/O pedal on the cleaner main body. [8]
5. Adjust the power level by rotating the variable power control roller*. [9]
6. Adjust the suction regulator* to the desired level. [10].
7. Switch o at the end of use by pressing the On/O pedal. Unplug and press the cord rewind
pedal to wind the power cord back into the cleaner [11].
8. Parking and Storage - The tube can be parked for temporary storage while in use, or in the
storage position when not in use [12].
*Certain Models Only ** Certain models only, nozzles may vary according to model
A. Main Cleaner
B. Cord Rewind Pedal
C. Carry Handle
D. Exhaust Filter Cover
E. On/O Pedal
F. Telescopic Tube*
G. Telescopic Tube Release Button*
H. Standard Tube*
I. Variable Power Control Roller*
J. Bag Check Indicator
K. Bag Door Release Latch
L. Suction Regulator*
M. Handle
N. Carpet and Floor nozzle(GP)**
O. Surface selector Peda **
P. Hose
Q. Pre motor lter
R. Exhaust lter
S. 2 in 1 Tool
T. Pet Hair Remover Mini Turbo Nozzle*
U. Allergen Remover Mini Turbo Nozzle*
V. Grand Turbo Nozzle*
W. Parquet nozzle*
N1. Carpet Nozzle (CA)**
N2. Hard Floor Nozzle (HF)**
Removing a Blockage From The System
If the bag check indicator is illuminated or ashing:
1. Check if the bag is full. If so refer to ‘Replacing The Dust Bag’.
2. If it is not full, then;
A. Do the lters need cleaning? If so refer to ‘Cleaning the Filter’.
B. Check if there is any other blockage in the system - Use a rod or a pole to remove any
blockage from the Teletube or exible hose.
Warning - The bag check indicator will turn red if the cleaner is used when full, if there is a
blockage or if the lters are dirty. If the cleaner is used for a signicant period of time with the
bag check indicator is red, a thermal cut out will switch the cleaner o to prevent overheating.
The bag check indicator turn green once the cleaner has switched o to signal that the thermal
cut out has been activated. If this should happen, switch the cleaner o, unplug and correct the
fault. It will take about 30 minutes for the cut out to automatically reset.
4

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hoover Capture CP10 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hoover Capture CP10 in de taal/talen: Alle talen als bijlage per email.

De handleiding is 2,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info