32489
3
Verklein
Vergroot
Pagina terug
1/8
Pagina verder
RTH2520 69-1867EF-1 13/6/06 3/4
3.2 Fan Operating Mode
Use the selector switch to set the fan to automatic
mode (AUTO) or continuous mode (ON).
Note: This switch is not used in a 2-wire installation
as the fan is not connected to the thermostat in this
type of installation.
3.3 Displaying the Temperature
The actual temperature is normally displayed. To view the setpoint,
press once on one of the buttons. The setpoint is displayed for
5 seconds along with the icon.
Note: Pressing either of the buttons more than once will
change the setpoint.
3.4 Setting the Temperature
Press one of the buttons until the desired temperature is dis-
played.
3.5 Backlight
The display illuminates for 12 seconds when the backlight button or
either of the buttons is pressed.
3.6 Thermostat Control Mode
3.6.1 Manual/Permanent Hold Mode
Maintains the temperature at a fixed setpoint. To place the thermo-
stat in this mode, press [ Mode ]. The house icon will disappear.
3.6.2 Programmable Mode
Maintains the temperature according to the energy-saving sched-
ule. To place the thermostat in this mode, press [ Mode ]. The cur-
rent period will be displayed. The four possible periods are:
To see the default program settings, see section 5.3.
Temporary Bypass
If you modify the setpoint (using the buttons) when the thermo-
stat is in Programmable mode, the thermostat will use the new set-
point for the next 2 hours. The house icon flashes during the
bypass. Afterwards the thermostat will return to the temperature set-
ting of the period currently underway.
3.7 Filter Replacement Indicator
After 500 hours of operation, an icon appears to indi-
cate that the filter needs replacement. Once the filter
is replaced, press [Filter] for 3 seconds to remove
the icon and reset the counter.
3.8 Battery Replacement Indicator
Install fresh batteries immediately when the icon starts
flashing. The icon flashes for 120 days before the bat-
teries are depleted. You should replace batteries once
a year or before leaving home for more than a month
even if the icon has not appeared.
After replacing the batteries, set the time, day and date (see sec-
tions 5.1 and 5.2). However, the temperature and program settings
are saved and do not need to be re-entered.
Warning: Before removing the batteries, place the
system switch on the thermostat to Off. Otherwise, the
heating/cooling unit might still be running even after
the batteries are removed.
n To access the configuration menu, press the backlight button
for 3 seconds.
o To go to the next parameter (menu item), briefly press the back-
light button.
p To modify a parameter, press .
q Repeat steps 2 and 3 if necessary.
r Press the backlight button for 3 seconds to exit the configura-
tion menu.
5.1 Setting the Time and Day
n Press [ Clk ]. The hour flashes.
o Set the hour using .
p Press [ Clk ]. The minutes flash.
q Set the minutes using .
r Press [ Clk ]. The day flashes.
s Set the day using . (MO: Monday, TU: Tuesday,
WE: Wednesday, TH: Thursday, FR: Friday, SA: Saturday and
SU: Sunday).
t Press [ Exit ] to exit.
5.2 Setting the Date
The date is needed for automatic daylight savings changeover.
n Press [ Clk ] for 3 seconds to display the year.
AUTO
The fan operates only when the heating or cooling sys-
tem is On (typical setting).
ON
The fan operates continuously. Use this setting to
improve air circulation and air cleaning.
Wake up Leave for work Return home Sleep
4. Configuration Menu
DISPLAY DESCRIPTION DEFAULT OPTIONS
Temperature display °F °C or °F
Time display 12 h 12 h or 24 h
Early start
1
Off On or Off
Automatic daylight savings
changeover
2
Off On or Off
Heating cycles per hour
3
4
2, 3, 4, 5 or 6
4
Cooling cycles per hour
3
4
2, 3, 4, 5 or 6
5
1
When Early Start is On, the thermostat determines when to start heating or cooling
so that the desired temperature is reached at the set time.
2
When this function is On, the thermostat automatically switches to daylight savings
time on the second Sunday of March and to normal time on the first Sunday of
November (see section 5.2).
3
Use the Heat/Cool selector switch to switch between the heating parameter and the
cooling parameter.
4
For optimal heating control, use the setting that matches your system as follows:
2=30 min (steam, gravity), 3=20 min (hot water, 90%+ high-efficiency furnace), 4=15
min (gas or oil), 5=12 min (alternate setting for gas or oil), 6=10 min (electric).
5
The corresponding cooling cycle lengths are: 2=30 min., 3=20 min., 4=15 min.,
5=12 min., 6=10 min.
5. Programming
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honeywell RTH2520 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honeywell RTH2520 in de taal/talen: Engels, Frans als bijlage per email.

De handleiding is 0,92 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Honeywell RTH2520

Honeywell RTH2520 Gebruiksaanwijzing - Espanôl - 8 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info