32379
11
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
CT3451 PROGRAMMABLE THERMOSTAT
11 69-1620—1
TROUBLESHOOTING
Table 4. Frequently Asked Questions.
If ... Then ...
Display does not come on. Make sure the batteries are fresh and installed correctly.
Temperature display does not go lower than
40°F (4°C) or higher than 99°F (37°C during
programming.
Your thermostat has reached the temperature limit. Be sure the
setting range is from 40°F to 99°F (4°C to 37°C).
Display shows flashing or steady “bAtLo.” The batteries are low; replace them as soon as possible.
Temperature change occurs at the wrong
time.
Check the program times for the period in question. Be sure that
AM and PM indications are correct. Make sure the current day and
time are correct. Reprogram if necessary.
Heating does not come on. Check that the System switch is set to Heat.
Check the system fuse or circuit breaker and replace or reset, if
necessary.
Check for correct wiring and good connections.
If display is blank or displays “bAtLo,” install fresh batteries.
Allow time for the furnace to heat up and the fan to come on
before checking for heat at the register.
If the temperature setting is higher than the current room
temperature and the flame is displaying, the thermostat is
operating correctly. Contact a heating contractor for assistance.
Cooling does not come on. Check that the System switch is set to Cool.
Check the system fuse or circuit breaker and replace or reset, if
necessary.
Check for correct wiring and good connections.
If display is blank or says “bAtLo,” install fresh batteries.
The thermostat has a built-in time delay on cooling. Allow five to
ten minutes after changing the setting before the air conditioner
starts.
If the temperature setting is lower than the current room
temperature and the snowflake is displaying, the thermostat
is operating correctly. Contact an air conditioning contractor for
assistance.
The furnace cycles too frequently or the
system cycle length is too short or too long.
Adjust heat cycle rate in the Customize Your Thermostat section.
The thermostat current setting does not
match the displayed room temperature to
within plus or minus 1°.
Plug the wiring hole in the wall behind the mounting plate with
insulation to prevent drafts that can adversely affect thermostat
operation.
Be aware that it is normal for the current setting and the
displayed room temperature to differ occasionally.
During recovery from setback or setup, setting and displayed
room temperatures can differ for up to 30 minutes after recovery
period.
System on indicator ( = heat; = cool) is
lighted, but no warm or cool air is coming
from the registers.
Wait five minutes after seeing the flame or snowflake and check
the registers again. If there is no hot or cool air coming from the
registers, refer to “Heating does not come on” or “Cooling does not
come on.” If everything is checked contact you heating and air
conditioning contractor.
Thermostat backlight appears dim. Wait until Replace Battery indicator is illuminated and replace
batteries.
Replace batteries now.
System on indicator is flashing.
MInimum off-timer is in effect. Wait five minutes until the
minimum off-timer is complete.
11

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honeywell CT3451 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honeywell CT3451 in de taal/talen: Engels als bijlage per email.

De handleiding is 0,38 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Honeywell CT3451

Honeywell CT3451 Gebruiksaanwijzing - Français - 16 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info