613664
6
Verklein
Vergroot
Pagina terug
1/12
Pagina verder
6
Section
7: System Testing
The first two digits in the HR80UK display indicate the number
of received test messages, and the right-hand digit indicates
the field strength (1 = sufficient field strength, 5 = very good
field strength).
The red LED of the HC60NG indicates the field strength by
means of flashing (1 = sufficient field strength,
5 = very good field strength).
To deactivate Service mode:
Press the binding procedure button for 5 seconds or wait 5
minutes or remove and then re-insert the batteries.
The green LED on the HC60NG will flash once every 7 sec-
onds.
7.1 Service mode
The wireless contact between the radiator controller, the cen-
tral operating unit and a receiver unit is checked in Service
mode. This mode is for installer use only.
Test between HR80UK & HC60NG
1. Separate operating unit from coupling module (see Sec
-
tion 6)
2. Turn the adjustment dial until on
(open) appears in the display.
3. Turn adjustment dial two full rotations (720°) further until
tESt is displayed. Service mode is active.
The radiator controller transmits a test message to any
available HC60NG.
The field strength is indicate by the number of flashes of
the red LED (1 = sufficient field strength, 5 = very good
field strength).
4. Press the binding procedure button (page 8 - diagram
5
).
The radiator controller is ready to receive the test message
from the central operating unit.
Caution!
!
When selecting the operating site ensure
that the distance to wireless devices such as
wireless headphones, cordless phones etc. is
approx. 1-2m.
It is recommended to complete the system testing
before mounting the wall bracket on the wall.
Position the CM67z Room Unit as close as pos-
sible to the location where it will be used.
Typical example of Building Fabric Signal losses
CM67z Room Unit to HR80UK Radiator Controllers
1. Move the CM67z slider to
AUTO position.
2. Set the
zone 1 setpoint to 5°C by pressing the TEMP
button. Press the
z1 z2
button and set the zone 2 setpoint
to 30°C by pressing the TEMP
button.
3. Check all the HR80UK’s in
zone 1 received 5°C setpoint
and the ones in zone 2 30°C setpoint (allow 4 minutes for
the HR80UK to receive the setpoint).
Repeat the steps 2 and 3 selecting different temperature values.
4. To complete the system test move the CM67z slider to the
OFF position then back to the AUTO position. Install the
wall bracket for the CM67z (if required).
HR80UK Radiator Controllers to HC60NG
1. Move the CM67z slider to AUTO position.
2. Set both
zone 1 and zone 2 setpoints to 5°C by pressing
the TEMP
button (Using the
z1 z2
button to switch
between zones).
3. Set all HR80UK dials to the
OFF position. Set the dial of
the first HR80UK to the ON position. The green LED on the
HC60NG should come on.
4. Set the dial back to the
OFF position and ensure that the
green LED on the HC60NG boiler controller goes off.
5.
Repeat the steps 3 and 4 with all the HR80UK’s in the system.
6. To complete the system test reset all of the HR80UK
radiator controllers back to normal operation by removing
and re-inserting the batteries on each one. Install the wall
bracket for the CM67z (if required).
Test between CM67z & HR80UK
1.
CM67z room unit can send a test signal to the HR80UK radia-
tor controllers and the HC60NG boiler or zone valve controller.
2. Set the CM67z slider to the OFF
position. Press the TEMP ,
and PROG 2 buttons together to
enter the test mode. The CM67z
will display:
z1 z2
Wall Wall Wall
Ceiling
Max. Signal Length 30 meters
= Signal Strength
6

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Honeywell CM67z bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Honeywell CM67z in de taal/talen: Engels als bijlage per email.

De handleiding is 1,04 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info