518473
3
Verklein
Vergroot
Pagina terug
1/29
Pagina verder
54
GB
GB
ASSEMBLY AND INSTRUCTIONS FOR USE :
1. Unpack the product. Wipe off dust with a damp cloth.
2. Familiarize yourself with the pump. The pump speed is controlled by the switch located at the
front of the pump. The speed is indicated by a plus (+) and minus (-) sign. To increase the
speed, move the switch slowly downward in the direction of the plus sign. At its highest speed
level, the switch will cease to move any further. To decrease the pump speed, move the switch
upward toward the minus sign. Similarly, at its lowest speed, the switch will cease to move any
further (Fig 9). NOTE: It is recommended the pump be set at its highest speed during
assembly and later adjusted to a lower setting if desired. Be sure to unplug the pump before
adjusting the speed setting.
3. Lead the cord through the cord slot on the bottom of the Base (A). This will ensure that the
unit is balanced when placed on a flat surface. Attach the A/C adaptor jack to the base
power cord. DO NOT plug into outlet at this time. See Figure 1.
4. Slide the waterproof light into the socket clip attached at the inner side of the slate holder (C).
5. Attach the large end of the tube to the connector located under the Top Slate (B). See figure 1.
6. Take the tube on the bottom side of the Top Slate (B) and place it through the Slate Holder
(C). Place this all the way so that you can see the tube through the opening on the back of
the Slate Holder (C). See Figure 2. NOTE: When placing the top slate (B) onto the slate
holder (C) be sure to line up the top slate notches with the slate holder cut-outs.
7. Place the Slate Holder (C) with the Top Slate attached (B) evenly across the Base (A).
Connect the small end of the tube to the pump. See Figures 3 and 4. NOTE: When placing
slate holder (C) onto Base (A), be sure to line up the opening of slate holder (C) with the
notches on Base (A).
8. Insert the Slate (D) into the “U” shaped slot (lowest) on the back of the Slate Holder (C), to
cover the pump. Insert Slates (E, F, G) into the Slate Holder as illustrated in the diagram. See
Figure 5. NOTE: This is the slate positioning that we recommend. The slates are
interchangeable and will fit into any of the slots on the Slate Holder. The slates can be
arranged differently - by pulling the slates in or out - the fountain will produce different water
patterns and sounds.
9. Arrange the stones provided onto the base and slates. See Figure 6.
10.Look through the opening on the back of the slate holder and fill the entire bottom of the
base, up to the bottom Slate Holder, with clean water. Water should be visible through the
back opening in the slate holder but should not be rising above the bottom of the Slate
Holder.
11.Plug the cord into 230V mains outlet. The fountain is controlled by the switch located on the
power cord. If pump doesn’t operate, rotate in-line switch once to turn “on” and once more to
turn “off”. NOTE: Ensure that the electrical cord loops below the electrical outlet to form a ‘Drip
Loop’ (Fig. 7). This will prevent water from running down the cord into the electrical outlet.
Stones
Switch
Adaptor
Cord Slot
Waterproof light
(A) Base
Slate (G)
Slate (F)
Slate (E)
(D) U-Shaped Slate
Slate Holder
(B) Top Slate
Light Socket Clip (C)
Pump
Tube
Figure 1 Figure 2
C
B
Figure 3
A
B
C
Cut-outs
Notches
Opening
Figure 6
Figure 4
Figure 5
A
B
C
D
E
F
G
Opening
Notches
Drip Loop
Figure 7
3

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Homedics WFL-ROC-3 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Homedics WFL-ROC-3 in de taal/talen: Nederlands, Duits, Engels, Frans, Italiaans, Spaans, Pools als bijlage per email.

De handleiding is 0,88 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info