30182
29
Verklein
Vergroot
Pagina terug
1/30
Pagina verder
GLOSSARY
GLOSSARY - Page 57Helicopter Flight Trimming Chart - Page 56
Helicopter Flight Trimming Chart
RPM Stick Primary Corrective Action
High Below 1/2 Decrease hovering throttle
Low Below 1/2 Decrease hovering pitch
Perfect Below 1/2 Decrease hovering throttle, decrease hovering pitch
High 1/2 stick Increase hovering pitch, decrease hovering throttle
Low 1/2 stick Decrease hovering pitch, increase hovering throttle
Perfect 1/2 stick Don't touch a thing!
High Above 1/2 Increase hovering pitch
Low Above 1/2 Increase hovering throttle
Perfect Above 1/2 Increase hovering pitch, increase hovering throttle
Want more Keep 1/2 Decrease hovering pitch, then increase hovering throttle
Want less Keep 1/2 Increase hovering pitch, then decrease hovering throttle
Adjusting Hovering Pitch and Hovering Throttle
This procedure assumes helicopter is trimmed for hovering. Trimming must be done in near-calm conditions.
Repeat tests several times before making adjustments. If any changes are made,
go back over the previous steps and verify, or further adjust as necessary.
The abbreviations used with the Optic are defined below alphabetically.
Related pages are given in parenthesis following the definition.
A
ACGL Acrobatic/Glider aircraft menu (15)
ADIF Aileron differential. Ailerons move more to one
side than other (31)
AILV Differential elevator servos, for 3-D aerobatics (39)
ATL Adjustable Travel Limit. Limits throttle trims to
only the throttle idle position.
(built in to your system)
A->R Aileron Rudder mixing (36)
C
CAMB A function which droops or raises the entire
trailing edge of a wing. (32)
COPY Data copy: command used to copy one memory
to another (11)
CROW Airbrake function (37)
CURSOR Button used to step through menus (9)
D
D/R Dual rate: switch-controlled function reduces
control travels. (27)
DATA Editing keys change numbers (9)
E
ELVN Elevon function combines ailerons & elevators for
tailless models. (34)
EPA End Point Adjust. Function that adjusts the servo t
ravel at the left and right sides. (27)
EXP Exponential function, reduces sensitivity around
neutral (28)
E->F Elevator Flap mixing (36)
F
FAIL Failsafe function moves servos to preset locations
if interference is received. (41)
FLPN Flaperon function gives the ailerons a flap
function. (30)
FLPT Flap travel function. (30)
G
Gear Landing gear control switch. (8)
GYRO Gyro setting menu (51)
H
HELI Helicopter settings menu. (45)
HOLD Throttle hold function holds the throttle in a near-
idle position (used for autorotation). (51)
I
INH Inhibit. Function will not operate
L
L/U Indicates Left or Up stick motion
LAND Landing function (33)
Lock Lock throttle button (9)
M
MAS Master channel in mixer (38)
M.SEL Model select menu (11)
N
NOR Normal helicopter swashplate (1 servo each for
elevator, aileron, pitch. (12)
O
OFF Function or Switch in OFF position.
ON Function or Switch in ON position.
P
PPM Pulse-Position Modulation,
also known as "FM". (14)
PCM Pulse-Code Modulation. (14)
PMX Programmable mixer. Mixing between
arbitrary channels. (38)
PTCV Pitch curve function (53)
Q
QPCM Pulse-Code Modulation. (14)
R
R/D Indicates Right or Down stick motion
REV Reverse. Servo operating direction
switching function. (29)
REST Reset model memory (15)
RVMX Revolution mixing (54)
R->T Rudder Throttle mixing (50)
S
S/W SEL Select on-off switches for different functions (39,53)
SFT.N Negative transmit shift direction (13)
SFT.P Positive transmit shift direction (13)
SLV Slave channel in program mixer (38)
STCK Choose Mode of transmitter. (13)
STRM Subtrim function used to adjust
servo neutrals. (28)
SWAH Swash type (12,54)
T
T.CUT Throttle cut function used to kill engine
without moving trims (29)
THCV Throttle curve function (52)
TIME Timer/Stopwatch function (14)
V
VTAL V-tail function combines the
elevators and rudder. (35)
Numerical
120' Helicopter swashplate, 120
°
(12,54)
To test for... Test Procedure Observations Adjustments
1. RVMX mixing
- Up settings
(Part 1)
Fly the model straight and
level into the wind at 100 ft
altitude, lower pitch to 0
°
Observe rotation as helicopter descends
A. No rotation
B. Model rotates counterclockwise
C. Model rotates clockwise
A. None
B. Add right rudder trim
C. Add left rudder trim
2. RVMX mixing
- Up settings
(Part 2)
Bring the helicopter into hover,
add full pitch and ascend 75 ft
Observe rotation as helicopter ascends
A. No rotation
B. Model rotates counterclockwise
C. Model rotates clockwise
A. None
B. Increase UP RVMX mix
C. Decrease UP RVMX mix
3. RVMX Down
mixing settings
Begin Down RVMX mixing
with same number as UP
mix. From inverted flight
(top of loop, or mid-point of
roll, or inverted part of split-S),
add full negative pitch
Observe rotation as helicopter ascends
A. No rotation
B. Model rotates clockwise
C. Model rotates counterclockwise
A. No adjustment
B. Increase Down RVMX mix
C. Decrease Down RVMX mix
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec OPTIC_6 bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec OPTIC_6 in de taal/talen: Engels als bijlage per email.

De handleiding is 2,02 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Hitec OPTIC_6

Hitec OPTIC_6 Gebruiksaanwijzing - Français - 60 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info