30178
5
Verklein
Vergroot
Pagina terug
1/6
Pagina verder
- Check to see if both servos and/or speed control are working properly.
If not, check the connections and/or make sure the main battery pack is charged.
- Check to see if the servos are moving in the correct direction. If not, change the
servo-reversing switch located on the top of the transmitter to achieve the correct direction.
- If everything checks out then turn the receiver "OFF" first, then the transmitter (Always
remember Never have the receiver "ON%#without the transmitter being %ON%this means
when turning your model %ON% always turn the transmitter "ON% first and %OFF% last)
Warning!!! : Do not shorten the length of the receiver antenna by cutting off any excess wire
as this will severely affect the operating range and could result in injury to yourself and others.
- Steering Servo Trim Setting
After verifying that the steering direction is correct, set the steering trim knob to the center,
the servo horn or arm should be at 90 degrees and the wheels should be straight. If not,
then make the horn or arm 90 degrees by removing it and replacing it correctly.
If the arm is at 90 degrees and the wheels are not straight, adjust the linkage to compensate.
Once you' ve got these two setting correct then use the steering trim for fine-tuning.
Note: (Always Trim your car before you run or race) This is a common mistake made by
beginners, if you have to steer your car to go straight, you are fighting a losing battle.
Make sure it goes straight before you run and driving will become much easier.
b. Throttle Servo Settings
- Using Mechanical Speed Control
Adjust the servo link rod so that point "B" will come to the neutral position. Also when the
trigger is pulled to the maximum point "C" should be as illustrated and at point "A" when the
trigger is pushed to the limit. Check to see if the vehicle moves forward when the trigger is
pulled. If the vehicle moves backwards then the "Throttle" reversing switch will need to be
switched. If the model moves forward or reverse at the neutral position then use the throttle
servo trim to fine tune. If the servo moves the speed control farther than is needed, you will
need to limit the travel by moving the linkage into a different mounting hole on the horn,
closer to center will give less travel and further from center will give more travel.
7 8
Ilqh#Wxqlqj
Wlowlqj#UljkwWlowlqj#Ohiw
"
#
$
$
#
"
www.hitecrcd.com
AM
PR OPORT IONA L
ON
5

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec LINX_SPORT bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec LINX_SPORT in de taal/talen: Engels als bijlage per email.

De handleiding is 0,58 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info