30180
13
Verklein
Vergroot
Pagina terug
1/16
Pagina verder
+
-
AUX
EDIT
EDIT
Auto Dual Rate:
This feature allows you to select individual high and low speed steering travel. First you must set the
throttle position where the rate will switch from #1 to #2. This is done by pulling the trigger to the
desired position and pushing the “Data” inc/dec buttons simultaneously. A “%” will show up on the
screen, this is the throttle % where the rate will change from #1 to #2, at this point, if you wish to
change it repeat the procedure again. Next, select the travel you wish to associate with the #1 and
#2 settings. This is done agter you exit the set up menu. Select the dual rate slide switch to the left,
adjust the #1 setting then pull the trigger until the #2 appears. You will use this feature to gain more
high or low speed steering according to throttle position. Important: Always allow the D/R setting to
“Auto Save” by letting the voltage re-appear on the screen before proceeding with any other
adjustments, this takes approximately 2 seconds.
Racer Tip
Auto D/R
Unique to the Lynx 3D, Auto Dual Rate can be a big advantage when you need to have more high speed
steering than low speed or vice versa. Let’s say your car is understeering (Pushing) under power but
oversteering (Loose) when you let off the throttle entering the corner. With the Auto D/R setting you can
select two different rates that will change at the programmable throttle position you select (refer to the
programming instructions on how to select settings). You would then select the #1 position to have
reduced travel and the #2 position to have more. Swap the settings on #1 and #2 for a car that oversteers
at high speed and understeers at low speed.
Standard Dual Rate
A must have for any race, this feature is adjusted from the digital switch marked D/R on the handle. To
distinguish from Auto D/R to standard D/R the dual rate switch on the front of the transmitter must be
selected to the right, it will read #3 on the display screen when accessed. Use the dual rates to fine tune
the handling of the vehicle by increasing or decreasing steering servo travel. If the vehicle is oversteering
(Loose) pull back on the switch to decrease the steering. If it is understeering (Pushing) increase the
steering by pushing the switch forward. The percentage of steering will automatically pop up on the LCD
screen. You can bump it one percentage point at a time fro fine tuning or hold it down for a more drastic
change. Continue to adjust this setting until the vehicle is more controllable and handling the way you
want.
$XX X XX X $XX X X
XX X
0
0
1
1
1
1
2
%%
%
%
%
%
CHANNEL
AUTO D/R
AUTO D/R
AUTO D/R
EPA POINT
POINT
POINT
POINT
EXP
12
EPA
POINT : 0 -- 100%
EXP
BLINKING
BLINKING
BLINKING
CH2 STICK SELECT
(DEC/INC PUSH TOGETHER)
POINT
DATA 1 DATA 2
SETTING POINT LOW : DATA 1
SETTING POINT HI : DATA 2
NOT SETTING POINT : DATA 1
13

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitec LINX_3D bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitec LINX_3D in de taal/talen: Engels als bijlage per email.

De handleiding is 1,66 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info