381303
23
Verklein
Vergroot
Pagina terug
1/26
Pagina verder
21
English
3. Plastic case 4. Hook
Optional accessories are subject to change without
notice.
APPLICATIONS
Tightening hex-head screws
Tightening drywall screws, wood screws and self-
drilling screws.
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, inviting serious
accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Confirm the direction of bit rotation (Fig.1)
The bit rotates clockwise (viewed from the rear
side) when the reversing switch lever is set to the
R side position. When the lever is set to the L
side position, the bit rotates counterclockwise and
can be used to loosen and remove screws.
5. Adjusting the tightening depth (Fig.2)
Pull the lock sleeve in the direction of arrow to
remove it from the spline installed in the gear
cover. While pulling the lock sleeve and turning it
right and left, adjust the position of locator. Push
the lock sleeve and align the gear cover spline with
the lock sleeve spline.
The lock sleeve can be inserted onto the gear cover
spline and locked.
(1) For hex-head screws:
Mount a hex-head screw on the hex-socket and set
the distance between the sub-stopper end and the
screw head neck to 1 1.5 mm, as shown in Fig.3.
(2) For drywall screws:
Mount a drywall screw on the bit, and set the
distance between the sub-stopper end and the screw
head to 1.5 2 mm, as shown in Fig.4.
(3) For cross-recessed self-drilling screws:
Mount a self-drilling screw on the bit, and set the
distance between the sub-stopper end and the screw
head bottom to 1 1.5 mm, as shown in Fig.5.
6. Mounting the bit
For details, refer to the item Mounting and
dismounting the bit.
MOUNTING AND DISMOUNTING THE HEX-
SOCKET OR THE BIT
1. Dismounting the hex-socket (Fig.6)
(1) While rotating the Sub-Stopper pull it out from the
locator.
(2) Remove the hex-socket, hold it with the opposite
side of bit by hand or vise and pull out the bit with
pliers.
2. Dismounting the bit (Fig.7)
Remove sub-stopper (A) as the same manner of
hex-head socket and remove the bit holder, then
pull out the bit with pliers.
3. Dismounting the bit (Fig.8)
Remove the sub-stopper (C) as the same manner
of hex-head socket and remove the bit holder, then
pull out the bit with pliers.
4. Mounting the hex-socket or the bit
Install the bit in the reverse order to removal.
HOW TO USE THE SCREW DRIVER
1. Switch operation and rotational speed
adjustment
Bit rotational speed can be adjusted between 0
4000/min (W6V3) or 0 2600/min (W6VA3, W6VB2)
or 0 1700/min (W8VB) varying the degree by
which the trigger switch is pulled. Rotational speed
increases as the trigger switch is pulled, and reaches
a maximum speed of 4000/min (W6V3) or 2600/min
(W6VA3, W6VB2) or 1700/min (W8VB) when the
trigger switch is pulled fully.
To facilitate continuous operation, pull the trigger
switch and depress the switch stopper. The switch
will then remain ON even when the finger is released.
By pulling the trigger switch again, the switch
stopper disengages and the switch is turned OFF
when the trigger switch is released.
2. Screw Driver operation
When the switch is turned ON, the motor starts to
run but the hex-socket (or the bit) does not rotate.
Attach the hex-socket to the screw head groove,
and push the Screw Driver against the screw. The
hex-socket then rotates and tightens the screw.
CAUTION
Ensure that the Screw Driver is held truly
perpendicular to the head of the screw.
If held at an angle, the driving force will not be
fully transferred to the screw, and the screw head
and/or hex-socket will be damaged. Hex-socket
rotation stops when pushing force is released.
3. Direction of hex-socket rotation
The hex-socket rotates clockwise (viewed from the
rear side) when the reversing switch lever is set
to the R side position. When the lever is set to
the L side position, the hex-socket rotates counter-
clockwise, and can be used to loosen and remove
screws.
CAUTION
Never change the direction of hex-socket (or bit
holder) rotation while the motor is running. To do
so would seriously damage the motor. Turn the
power switch OFF before changing the direction
of hex-socket (or bit holder) rotation.
23

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi w 8 vb bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi w 8 vb in de taal/talen: Engels, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,36 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Andere handleiding(en) van Hitachi w 8 vb

Hitachi w 8 vb Gebruiksaanwijzing - English - 30 pagina's


Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info