387422
29
Verklein
Vergroot
Pagina terug
1/32
Pagina verder
27
English
mark " " or the hammer mark" " to the triangle
mark of the housing.
To make holes in the metal, wood or plastic, switch
to "Rotation (Rotation only)".
To make holes in bricks or concrete blocks, switch
to "Impact (Impact + Rotation)".
CAUTION
If an operation which is normally performed at the
"Rotation" setting is performed at "Impact " setting,
the effect of making holes does not only increase
but it may also damage the bit or other parts.
4. Change rotation speed
Operate the shift knob to change the rotational
speed. Move the shift knob in the direction of the
arrow (see Figs. 5 and 6).
When the shift knob is set to L, the drill rotates
at a low speed. When set to H, the drill rotates
at a high speed.
CAUTION
When changing the rotational speed with the shift
knob, confirm that the switch is off.
Changing the speed while the motor is rotating will
damage the gears.
When setting the shift knob to H (high speed) and
the position of the cap is 4 or 5, it may happen
that the clutch does not engaged and that the motor
is locked. In such a case, please set the shift knob
to L (low speed).
If the motor is locked, immediately turn the power
off. If the motor is locked for a while, the motor
or battery may be burnt.
5. The scope and suggestions for uses
The usable scope for various types of work based
on the mechanical structure of this unit is shown
CAUTION
Align the number and mark on the cap to the
triangle mark of the housing. The middle point of
the numbers and marks on the cap cannot be
secured.
2. Tightening torque adjustment
(1) Tightening torque
Tightening torque should correspond in its intensity
to the screw diameter. When too strong power is
used, the screw head may be broken or be injured.
Be sure to adjust the cap position according to the
screw diameter.
(2) Tightening torque indication
Tightening torque should be changed according to
the screw type and the materials to be tightened.
Guidance of the tightening torque is indicated on
the cap of this unit with numerals 1, 2, 3,
4 and 5. The minimum power is from 1
position and bigger the value the stronger is the
power (see Fig. 4).
(3) How to adjust the tightening torque
Rotate the cap and set to one of the numerals.
Adjust the torque by cap rotation in such a way that
when the torque is too strong, set to the next
smaller numeral and set to the next larger numeral
when too weak.
CAUTIONS
The motor rotation may be locked to cease while
the unit is used as drill. While operating the impact
drill, take care not to lock the motor.
Too long hammering may cause the screw broken
due to excessive tightening.
3. Rotation to Impact changeover (See Fig. 4.).
The "Rotation (Rotation only)" and "Impact (Impact
+ Rotation)" can be switched by aligning the drill
Work Usable range Suggestions
Drilling
Brick: 10 mm
Use for drilling purpose.
Wood: 18 mm
Steel: 10 mm
Aluminum: 10 mm
Driving
Machine screw: 6 mm
Use the bit and socket matching the
screw diameter.
Nut: 5 mm
Wood screw: 5.1 mm (diameter) x 32 mm (length) Use after drilling a pilot hole.
6. How to select tightening power and rotational speed
Table 2
Use Cap Position
Rotating speed selection (Position of the shift knob)
L (Low speed) H (High speed)
Driving
Machine screw 1 5
F
or 4 mm or sma
ll
er
di
ameter
screws.
F
or 5 mm or
l
arger
diameter screws.
Wood screw 1 5 For 3.5 mm or smaller nominal
diameter screws.
For 3.8 mm or larger
nominal diameter screws.
Drilling
Brick ––––––
F
or
d
r
illi
ng w
i
t
h
a
b
r
i
c
k
working drill.
Wood For 10 mm or larger diameters.
F
or 10 mm or sma
ll
er
diameters.
Metal
F
or
d
r
illi
ng w
i
t
h
an
i
ron
working drill.
––––––
For drilling with a carbide
tipped drill bit.
For drilling with a metal
working drill bit.
CAUTION
The selection examples shown in Table 2 should be considered as general standard. As different types of
tightening screws and different materials to be tightened are used in actual works proper adjustments are
naturally necessary.
Table 1
29

Hulp nodig? Stel uw vraag in het forum

Spelregels

Misbruik melden

Gebruikershandleiding.com neemt misbruik van zijn services uitermate serieus. U kunt hieronder aangeven waarom deze vraag ongepast is. Wij controleren de vraag en zonodig wordt deze verwijderd.

Product:

Bijvoorbeeld antisemitische inhoud, racistische inhoud, of materiaal dat gewelddadige fysieke handelingen tot gevolg kan hebben.

Bijvoorbeeld een creditcardnummer, een persoonlijk identificatienummer, of een geheim adres. E-mailadressen en volledige namen worden niet als privégegevens beschouwd.

Spelregels forum

Om tot zinvolle vragen te komen hanteren wij de volgende spelregels:

Belangrijk! Als er een antwoord wordt gegeven op uw vraag, dan is het voor de gever van het antwoord nuttig om te weten als u er wel (of niet) mee geholpen bent! Wij vragen u dus ook te reageren op een antwoord.

Belangrijk! Antwoorden worden ook per e-mail naar abonnees gestuurd. Laat uw emailadres achter op deze site, zodat u op de hoogte blijft. U krijgt dan ook andere vragen en antwoorden te zien.

Abonneren

Abonneer u voor het ontvangen van emails voor uw Hitachi dv 10 dva bij:


U ontvangt een email met instructies om u voor één of beide opties in te schrijven.


Ontvang uw handleiding per email

Vul uw emailadres in en ontvang de handleiding van Hitachi dv 10 dva in de taal/talen: Engels, Deens, Zweeds, Noors, Fins als bijlage per email.

De handleiding is 0,49 mb groot.

 

U ontvangt de handleiding per email binnen enkele minuten. Als u geen email heeft ontvangen, dan heeft u waarschijnlijk een verkeerd emailadres ingevuld of is uw mailbox te vol. Daarnaast kan het zijn dat uw internetprovider een maximum heeft aan de grootte per email. Omdat hier een handleiding wordt meegestuurd, kan het voorkomen dat de email groter is dan toegestaan bij uw provider.

Uw handleiding is per email verstuurd. Controleer uw email

Als u niet binnen een kwartier uw email met handleiding ontvangen heeft, kan het zijn dat u een verkeerd emailadres heeft ingevuld of dat uw emailprovider een maximum grootte per email heeft ingesteld die kleiner is dan de grootte van de handleiding.

Er is een email naar u verstuurd om uw inschrijving definitief te maken.

Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken

U heeft geen emailadres opgegeven

Als u de handleiding per email wilt ontvangen, vul dan een geldig emailadres in.

Uw vraag is op deze pagina toegevoegd

Wilt u een email ontvangen bij een antwoord en/of nieuwe vragen? Vul dan hier uw emailadres in.



Info